Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 8 of 8
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Jul 2009
    Posts
    75
    Rep Power
    30

    Taskalfa 500ci not booting up

    After installing a new engine board and new hard drives on a Taskalfa 500ci, machine was stuck on welcome screen. Switched machine off and on it then displayed C0640 error code. Formatted hard drive now machine is stuck on "now restoring data to hard drive" By the way its a new machine

  2. #2
    Master Of The Obvious 10,000+ Posts
    Taskalfa 500ci not booting up

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,444
    Rep Power
    462
    You need to reload firmware immediately after replacing the engine board. You can still reload the firmware.

    There are two different types of engine PWBs. Did you order and install the same type? =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  3. #3
    Trusted Tech 50+ Posts
    Join Date
    Jul 2009
    Posts
    75
    Rep Power
    30
    version 8 firmware was loaded.
    PARTS PWB ENGINE ASSY SP
    2H794070 was the part ordered

  4. #4
    Master Of The Obvious 10,000+ Posts
    Taskalfa 500ci not booting up

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,444
    Rep Power
    462
    Quote Originally Posted by brancas View Post
    version 8 firmware was loaded.
    PARTS PWB ENGINE ASSY SP
    2H794070 was the part ordered
    Current firmware is v. 9.01

    Did the old PWB have 2H94070 printed on it?
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  5. #5
    Trusted Tech 50+ Posts
    Join Date
    Jul 2009
    Posts
    75
    Rep Power
    30
    there was no part no. just a serial no.

  6. #6
    Master Of The Obvious 10,000+ Posts
    Taskalfa 500ci not booting up

    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    22,444
    Rep Power
    462
    I wonder if I'm interpreting this tip wrong...

    There is definitely a different engine board for the lower segment machines than the higher segment machines. From a certain point of view that's two different engine boards. The parts manual lists only one part number for the higher segment machines-the number you ordered. OK, so disregard the second suggestion.

    Did all the firmware successfully load? Pay particular attention to the last screen. Which one or ones failed? If it's engine or Hi voltage that fails, you may need to contact the hotline to get a special form of the firmware with engine firmware only. And no, you can't just pick out a single file to load. You'll load the special firmware first, then if that succeeds load the combined firmware. =^..^=
    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.
    3) if you're going to ask about jams include the jam code.
    4) if you're going to ask about an error code include the error code.
    5) You are the person onsite. Only you can make observations.

    blackcat: Master Of The Obvious =^..^=

  7. #7
    Junior Member spannerman's Avatar
    Join Date
    May 2009
    Posts
    2
    Rep Power
    0
    Did you swap the eeprom from the old board to the new?

  8. #8
    Trusted Tech 50+ Posts
    Join Date
    Jul 2009
    Posts
    75
    Rep Power
    30
    installed ver 9.01 firmware and re connected connections to engine board, machine working, thanks 4 the info.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here