• ernesto's Avatar
    6 Minutes Ago
    ernesto replied to a thread [CQ] IR 2016 wrinkled paper in Canon
    Hi Maybe there is dirty on the guide before the roller pressure.........you can try to clean it. ALL THE BEST
    1 replies | 18 view(s)
  • canonbundy's Avatar
    44 Minutes Ago
    I found a couple of items that may help. Symptom Swapped the ITB assembly with another working machine. The E075 returned on the customer's...
    3 replies | 90 view(s)
  • ernesto's Avatar
    21 Hours Ago
    ernesto replied to a thread [Dead] Canon iR2020i - loading problem..... in Canon
    You can try this, maybe it works. if you can insert the K2-5725-000 1 MEMORY, USB FLASH, 128M of other ir2020i, when you turn on the machine,...
    3 replies | 84 view(s)
  • canonbundy's Avatar
    1 Day Ago
    Could be dirty/faulty sensor in DADF tray giving false reading or maybe try reinit the DADF in SRV Mode Tray Width.
    4 replies | 66 view(s)
  • ernesto's Avatar
    2 Days Ago
    ernesto replied to a thread irc3480 curled paper in Canon
    Hi, If there are 0107 code jams ( jam behind small orange roller in the unit fixing) you can replace Fu5-1559-000 bushings ...
    2 replies | 65 view(s)
  • canonbundy's Avatar
    3 Days Ago
    canonbundy replied to a thread IR Advance C2020 in Canon
    Hi Hwoody, just like Vamoursly said "POS" - if the Unit/s have done less than 60% then a pro-rata warranty claim can be made through Canon (make sure...
    9 replies | 204 view(s)
  • ernesto's Avatar
    3 Days Ago
    ernesto replied to a thread [CQ] ir advance 400i in Canon
    Hi, The keypresses donīt work right, they are very slowly and it is nearly imposible to enter in service mode, I got it once...... turning on...
    8 replies | 178 view(s)
  • ernesto's Avatar
    3 Days Ago
    ernesto replied to a thread [CQ] ir advance 400i in Canon
    HI What model did you have doing that ? I hope to hear from you
    8 replies | 178 view(s)
  • canonbundy's Avatar
    5 Days Ago
    canonbundy replied to a thread [Error Code] Canon irAdv 7065 in Canon
    As Canuck said, also check the Red Painted Screw (that you probably unscrewed) in the Upper Belt assy & reposition. Aussies kickin' ur ass too in...
    5 replies | 207 view(s)
  • ernesto's Avatar
    6 Days Ago
    ernesto replied to a thread Muleme stephen.k in Canon
    Hi, I had the same problem ( Error 197) four mounth ago....In my case it was the fixing unit...I swap it with other machine and both of them are...
    3 replies | 134 view(s)
  • ernesto's Avatar
    1 Week Ago
    Hi IRC 2380 does not need to reset drum, it is automatic. What do you have to do when you replace a drum in a taskalfa 250ci? All the best
    6 replies | 169 view(s)
  • ernesto's Avatar
    1 Week Ago
    ernesto replied to a thread [CQ] ir 2200 auto sleep time in Canon
    I got it Service mode... Copier...option....user....sleep....0 :-)
    2 replies | 72 view(s)
  • ernesto's Avatar
    1 Week Ago
    ernesto started a thread [CQ] ir 2200 auto sleep time in Canon
    Hi Does anyone know how to switch off the auto sleep time? In common settings it only can set up until 4 hours...:-( All the best
    2 replies | 72 view(s)
  • ernesto's Avatar
    1 Week Ago
    ernesto started a thread [CQ] ir advance 400i in Canon
    HI, Does anybody know this problem? https://www.youtube.com/watch?v=uaBYYoHWgNI Control panel or main controller? I hope hear from you...
    8 replies | 178 view(s)
  • canonbundy's Avatar
    1 Week Ago
    canonbundy replied to a thread [Error Code] ES 6530 C390 in Toshiba
    I had this 1 in a million situation whereby a tiny piece of plastic from the Y Toner cartridge wedged between the Toner Drive Gears & prevented the...
    2 replies | 130 view(s)
  • canonbundy's Avatar
    1 Week Ago
    canonbundy replied to a thread [Dead] Toshiba es352 no display, fans run in Toshiba
    Machine should cycle over to complete initialisation, try removing RAM & cleaning contacts or replacing. Clean all Addon PCB contacts, reseat all...
    5 replies | 123 view(s)
  • canonbundy's Avatar
    1 Week Ago
    Possibly the HDD may be too large however try the following. Clear+3 > P/ON > 3 - Update ONLY the SYS & HDD at this stage - if successful then...
    4 replies | 135 view(s)
  • ernesto's Avatar
    1 Week Ago
    ernesto replied to a thread [Dead] Irc 1028 if green light but no power in Canon
    Hi If you can print you can disconnect and connect the (1 WA7-4997-000 1 DIMM, SMD-N51226NP-D) in the main controller and sometimes the display...
    2 replies | 94 view(s)
  • ernesto's Avatar
    1 Week Ago
    ernesto replied to a thread CANON IR2270 ALWAYS JAMS in Canon
    HI http://www.copytechnet.com/forums/canon/72718-ir-4570-jam-0105-a.html All the best
    6 replies | 166 view(s)
  • canonbundy's Avatar
    1 Week Ago
    canonbundy replied to a thread CANON IR2270 ALWAYS JAMS in Canon
    Or cut a piece of mylar/thin plastic & stick to Flag - quick & cheap. Maybe replace Fixing Assy - Fixing Film grease may be gummy & not allowing...
    6 replies | 166 view(s)
  • ernesto's Avatar
    1 Week Ago
    ernesto replied to a thread CANON IR2270 ALWAYS JAMS in Canon
    HI If It jam in doble side mode.... I think the problem is the paper humidity....in a4r it'll work ...in a4 you should update firmware and...
    6 replies | 166 view(s)
  • canonbundy's Avatar
    1 Week Ago
    SRV Mode 2 > FUNC > CLEAR > REG > FUNC > LASER LD Y-M-C. ADD FUNC > Perform Quick Adjust > AUTO COLOUR CORRECTION.
    10 replies | 248 view(s)
  • canonbundy's Avatar
    2 Weeks Ago
    2nd drawer transport jam (not reaching the 1st drawer feed sensor) PFP upper drawer transport jam (not reaching the 1st drawer feed sensor) PFP lower...
    10 replies | 266 view(s)
  • ernesto's Avatar
    2 Weeks Ago
    ernesto posted a visitor message on northernlife's profile
    HI .. The problem with the irc 1028i was fixed I checked dc connectors and after that, it solved the problem.... :) All the best
  • ernesto's Avatar
    2 Weeks Ago
    ernesto replied to a thread [CQ] irc 1028i in Canon
    I checked dc connectors and after that, it solved the problem.... :) Thanks a lot. Mr Teckat
    5 replies | 919 view(s)
  • ernesto's Avatar
    3 Weeks Ago
    ernesto replied to a thread [CQ] irc 1028i in Canon
    I have seen that the problem is only in the color black when it combines with the other colors ( soft and perfect shadow in the letters). All the...
    5 replies | 919 view(s)
  • ernesto's Avatar
    3 Weeks Ago
    ernesto started a thread [CQ] irc 1028i in Canon
    I cannot do the gradation adjust what do you think about it...? I have exchanged the itb and all the cartridges and in service mode I executed the....
    5 replies | 919 view(s)
  • canonbundy's Avatar
    3 Weeks Ago
    Clean/replace Hopper Sensor - Clean Sensor in Dev Unit & check Sensor Wiper (loses cleaning ability) - replace Wiper ( attached to Toner Auger) -...
    7 replies | 681 view(s)
  • canonbundy's Avatar
    4 Weeks Ago
    Correct Toner Bottle inserted? 25 & 26 Bottles have different 'plugs'. When Toner Lever is pulled down does it lock the Bottle in firmly? Toner...
    4 replies | 549 view(s)
  • canonbundy's Avatar
    4 Weeks Ago
    canonbundy replied to a thread [Misc] Toshiba Estudio 650 Toner spilling in Toshiba
    OEM Toner? Clean/replace Hopper Sensor. Clean/replace Developer Sensor/Wiper. Developer overlife? The machine is being told to add Toner even...
    2 replies | 91 view(s)
More Activity

3 Visitor Messages

  1. body we replace already the toner sensor still the developer runs out of toner. my body suggest to replace d c controller. but its to expensive.
  2. hi bro.

    i have a problem bro.
    with the canon ir 5000. the developer unit got empty even the toner hopper have plenty of toner in the inside.

    please i need you help.

    thanks edpianix
  3. View Conversation
    Toshiba e5520c.my email tom@copymasteraz.com
    Thanks
Showing Visitor Messages 1 to 3 of 3
About canonbundy

Basic Information

Age
60
About canonbundy
Real Name:
Cliff Hurst
Country:
Australia
State/County:
au queensland
Where are you from (City, State):
Bundaberg Qld.
Biography:
I have been a Technician in Office Equipment 40+ years, I started with Typewriter, Adding Machine, Cash Register and Accounting machine repairs and through the Evolution of Technology change, Printers, Fax machines and Photocopiers including most brands, mainly Canon and Toshiba.
Interests:
Fishing and Camping, Golf and Horse Racing.
What Year Did You Start in this Industry:
1969
Most Hated Brand:
Hmmmm, probably no particular Brand but some Models can be 'at bit more challenging' than others.
What was the first machine you worked on:
An 'IMPERIAL 55' Typewriter.
Last machine you were formally trained on:
Canon IRA-C5000 series.
Gender:
Male

Statistics


Total Posts
Total Posts
564
Posts Per Day
0.73
Visitor Messages
Total Messages
3
Most Recent Message
07-31-2013
General Information
Last Activity
22 Minutes Ago
Join Date
06-16-2012
Referrals
0

4 Friends

  1. bipc bipc is offline

    Senior Tech

    bipc
  2. edpianix edpianix is offline

    Junior Member

    edpianix
  3. ernesto ernesto is online now

    Senior Tech

    ernesto
  4. tomcatt tomcatt is offline

    Technician

    tomcatt
Showing Friends 1 to 4 of 4

07-30-2014


07-29-2014


07-23-2014


07-07-2014