Tab Content
  • SAZ911's Avatar
    6 Days Ago
    SAZ911 replied to a thread [Misc] Canon IRA C5235i Slow Prints / Copies in Canon
    Hi, Will try a once over again this afternoon / tomorrow morning and ill let you know what happens....as soon as i know more, thanks for the...
    9 replies | 442 view(s)
  • SAZ911's Avatar
    6 Days Ago
    SAZ911 replied to a thread [Misc] Canon IRA C5235i Slow Prints / Copies in Canon
    Hi Zoraldinho, Checked Settings ? Registration for a settings that may be slowing it down, but i have found nothing as i did a MMI clear which...
    9 replies | 442 view(s)
  • SAZ911's Avatar
    1 Week Ago
    SAZ911 replied to a thread [Misc] Canon IRA C5235i Slow Prints / Copies in Canon
    Hi Zoranldinho, Thanks, that is a good idea, i will check and get back to you with what i find.........
    9 replies | 442 view(s)
  • SAZ911's Avatar
    1 Week Ago
    SAZ911 replied to a thread [Misc] Canon IRA C5235i Slow Prints / Copies in Canon
    Hi, Thanks for the suggestion, though the device is on my network at my office (No POE) and it also prints slow when used as a standalone copier...
    9 replies | 442 view(s)
  • SAZ911's Avatar
    1 Week Ago
    SAZ911 replied to a thread [Error Code] IRAdvC5250 - E674-0200 in Canon
    Something like this......? I have the same errors, though my issue is the device prints / copies slow duplex.....
    5 replies | 320 view(s)
  • ernesto's Avatar
    1 Week Ago
    ernesto started a thread IRC 1325i in Canon
    Hi I have an IR C1325i asking for toner magenta but it has. Does anyone know the problem? I look forward to hearing from you soon All the...
    0 replies | 139 view(s)
  • SAZ911's Avatar
    1 Week Ago
    Hi All, I have a Canon IRA C5235i that has an issue when printing, its seems to take a long time spooling, though when you check the status on the...
    9 replies | 442 view(s)
  • Canuck's Avatar
    1 Week Ago
    As stated earlier...but you don't wanna hear it. Printhead AND Main controller. I've seen fried printheads eat main controllers right when you...
    13 replies | 517 view(s)
  • Canuck's Avatar
    2 Weeks Ago
    This is why you run itb replacement before attempting to remove the assembly..obviously something got damaged on itb assembly
    11 replies | 449 view(s)
  • Canuck's Avatar
    2 Weeks Ago
    Canuck replied to a thread ir5055 half light in Canon
    Possibly HVT connector for transfer/sep corona assembly. They crack and leak. Its the one that the contacts on the rear of the trans/sep assembly...
    9 replies | 317 view(s)
  • Canuck's Avatar
    2 Weeks Ago
    Go into service mode and enable to display itb replacement in user mode. Then go to maintenance in user mode and execute it. This will move necessary...
    11 replies | 449 view(s)
  • Canuck's Avatar
    2 Weeks Ago
    Canuck replied to a thread [Error Code] Canon ir 2535 in Canon
    If bar stops then machine is not totally booting. This model has a flash drive instead of hard drive so I would look at that and reflash the machine...
    7 replies | 304 view(s)
  • ernesto's Avatar
    3 Weeks Ago
    ernesto started a thread ir advance 400 i in Canon
    There is no edge blank in the copies or page impressions Solution: replacing register clutch
    0 replies | 77 view(s)
  • ernesto's Avatar
    3 Weeks Ago
    are there two boards in this machine, one board work with yelow and black y the other board work with cyan and magenta???? if the answer is yes can...
    2 replies | 267 view(s)
  • ernesto's Avatar
    3 Weeks Ago
    ernesto started a thread irc1325i in Canon
    HI I have a problem with a irc1325i there are color and black and white lines everywhere it seems that the itb does not work but I replaced the...
    0 replies | 59 view(s)
No More Results

1 Visitor Messages

  1. View Conversation
    Hi, Canuck!

    That aab1 asshole sure is one irritating, SOB, isn't he?

    A couple of posts and he thinks he runs the site.

    You'd think he'd get the message and just go away, but nooooo.

    In my 3 years on Copytechnet, I've never seen anything like him.

    He not only needs to STFU, but GTFO, as well!!

    Regards,
    Ken
Showing Visitor Messages 1 to 1 of 1
About Canuck

Basic Information

About Canuck
Real Name:
mark
Country:
Canada
State/County:
ca ontario
Where are you from (City, State):
Southwestern Ontario
Biography:
20 year tech,single,musician
Interests:
music-guitar
Occupation:
tech
What Year Did You Start in this Industry:
1987
What was the first machine you worked on:
xerox
Last machine you were formally trained on:
canon imagepress
Gender:
Male

Statistics


Total Posts
Total Posts
1,477
Posts Per Day
0.41
Visitor Messages
Total Messages
1
Most Recent Message
11-09-2010
General Information
Last Activity
1 Week Ago
Join Date
11-13-2007
Referrals
1

3 Friends

  1. ernesto ernesto is offline

    Senior Tech

    ernesto
  2. lsamaroo lsamaroo is offline

    Technician

    lsamaroo
  3. SAZ911 SAZ911 is offline

    Senior Tech

    SAZ911
Showing Friends 1 to 3 of 3

10-12-2017


10-07-2017


09-26-2017