Tab Content
  • cucuklotz's Avatar
    3 Hours Ago
    cucuklotz replied to a thread Xerox Workcentre 7225 in Xerox
    Thank you Phil B again for replying.I tried to find Altboot for 7225,but could not find,I have tried many searches.I have found Altboots procedures...
    3 replies | 110 view(s)
  • dan7777's Avatar
    17 Hours Ago
    dan7777 replied to a thread [Error Code] CAON IRADVC5250i Error E0029-003 in Canon
    Check fuse FU2 on paper feed driver PCB.
    2 replies | 75 view(s)
  • cucuklotz's Avatar
    2 Days Ago
    cucuklotz replied to a thread Xerox Workcentre 7225 in Xerox
    Hi Thank you for replying.Il let you know how it works out. ...
    3 replies | 110 view(s)
  • cucuklotz's Avatar
    2 Days Ago
    cucuklotz started a thread Xerox Workcentre 7225 in Xerox
    Hi After powering up the WC7225,the machine never boots up.The green energy save button stays lite,and nothing else happens. No display or...
    3 replies | 110 view(s)
  • dan7777's Avatar
    1 Week Ago
    No it shows. iR 8500/105/7200/85.- iR 9070/105+/8070/85+
    7 replies | 221 view(s)
  • dan7777's Avatar
    1 Week Ago
    . Off the canon dealer website. It only uses the service support tool. I do not even mess with trying to get someone a file that big, sorry. I do...
    7 replies | 221 view(s)
  • dan7777's Avatar
    1 Week Ago
    You may have a hard time getting that. It shows 222Meg last version in Sept. 2008.
    7 replies | 221 view(s)
  • dan7777's Avatar
    1 Week Ago
    Check all the pages. Maybe someone moved it to another page. We move the scanner, ifax and others to pages you can not see. If it is not anywhere...
    4 replies | 194 view(s)
  • dan7777's Avatar
    1 Week Ago
    dan7777 replied to a thread CANON IR ADV c 7055 in Canon
    If you pull the magenta developer out and see those voids on the mag roller then problem is in developer. That is one developer you can take the dr....
    5 replies | 280 view(s)
  • dan7777's Avatar
    1 Week Ago
    dan7777 replied to a thread [Error Code] E020-391 IR5030i in Canon
    Very common. If you have the plus gear with pin then look at the part that drives it. It is a toss up weather to take out the drive assembly and...
    15 replies | 608 view(s)
  • dan7777's Avatar
    1 Week Ago
    dan7777 replied to a thread Canon Advance IRC2230 jams in Canon
    Glad you found the repair. On the newer models you can touch the jam code and it tells you sensor (with picture) and if delay or stationary. On error...
    8 replies | 342 view(s)
  • dan7777's Avatar
    2 Weeks Ago
    dan7777 replied to a thread Canon Advance IRC2230 jams in Canon
    Funny, I have one this morning jamming in the 2/3 delivery. 020B. 0205 is delay at reg flag. I had to replace that flag assembly on one of them. It...
    8 replies | 342 view(s)
  • dan7777's Avatar
    2 Weeks Ago
    dan7777 replied to a thread [CQ] IR C350 faded copies in Canon
    I go by percentage and mine get 80-120% before they go light with canon drums. I am going to guess that is 20-30 thousand copies.
    3 replies | 145 view(s)
  • dan7777's Avatar
    2 Weeks Ago
    dan7777 replied to a thread Canon Advance IRC2230 jams in Canon
    When you put in a fuser you have to take two screws off and put the assembly off old fuser on the new fuser. Those bushings get knocked out of place...
    8 replies | 342 view(s)
  • dan7777's Avatar
    2 Weeks Ago
    dan7777 replied to a thread Canon Advance IRC2230 jams in Canon
    When you put in a fuser you have to take two screws off and put the assembly off old fuser on the new fuser. Those bushings get knocked out of place...
    8 replies | 342 view(s)
  • dan7777's Avatar
    2 Weeks Ago
    Almost forgot. The hinges have been updated and I put in new hinges also. I think they were updated for that reason. It would feed from both right...
    3 replies | 172 view(s)
  • dan7777's Avatar
    2 Weeks Ago
    I did on a 6XXX series. It was the right door. Either warped or worn (the guides). I think canon had a update on a piece in the middle. It was on a...
    3 replies | 172 view(s)
  • cucuklotz's Avatar
    2 Weeks Ago
    THANK YOU SANDMANMAC I spoke to the customer after I saw your reply,I know their computer guy so I passed...
    3 replies | 132 view(s)
  • cucuklotz's Avatar
    2 Weeks Ago
    Hi When I searched code online I saw that it could be network related on many Ricohs,But did not see anything specifically on the 4310. Has...
    3 replies | 132 view(s)
No More Results

8 Visitor Messages

  1. Hi, And sorry I havnt gotten back to you. I will stop by customer today to get report.I will find out answer to your other questions also.
    THANKS ANDY
  2. View Conversation
    Hi Andy,
    Can you print and place in your post the communication report?
    You can delete the private information (telephone numbers) from report.
    Customer has a problems when he receive or transmit faxes?
    FAX connected to telephone line directly or through office ATE?
    Sashko
  3. View Conversation
    Hi, Andy,
    I replied on your post.
    Can you explain your problem in more detail?
    Sashko
  4. Good on ya Andrew.
  5. Hi Andrew,

    My name's Pete montgomery.
    Just dropping by to say G'day.

    I'm an Independent Xerox Tech In Sydney Australia.

    7 years at Xerox and 4 years self employed.

    I've just joined this here and see that you're a real contributor to this site so I decided to "Befriend" you.

    Pete.
  6. 6550--- Yup!
  7. Hello, I was curious if you ever fixed the problem with the intermittent jamming of the tray on the hp 4000? I would greatly appreciate it,
    thanks!
  8. Hello,I never did any upgrades to scaner,and if you add 256 RAM and I think MXNSX1 scan key (same as at ARM 256). Where to input software key: I think- key operator program, next five times zero,next product key , input 20 digits scan key. This is procedure for AR M450,must be the same for your model too. Tray to contact some other guys to,to be sure for my step.
Showing Visitor Messages 1 to 8 of 8
About cucuklotz

Basic Information

About cucuklotz
Real Name:
Andrew Klotz
Where are you from (City, State):
Brooklyn
Biography:
30 plus years copier exp.and a funny guy to boot
Interests:
Bowling and a good laugh
What Year Did You Start in this Industry:
1974
Most Hated Brand:
Minolta sucks
What was the first machine you worked on:
Apeco(Jamamatic)
Last machine you were formally trained on:
Sharp 161 series
Gender:
Male

Statistics


Total Posts
Total Posts
531
Posts Per Day
0.13
Visitor Messages
Total Messages
8
Most Recent Message
12-30-2009
General Information
Last Activity
3 Hours Ago
Join Date
03-12-2007
Referrals
0

3 Friends

  1. dan7777 dan7777 is offline

    Field Supervisor

    dan7777
  2. ernesto ernesto is offline

    Senior Tech

    ernesto
  3. Peter Montgomery Peter Montgomery is offline

    Technician

    Peter Montgomery
Showing Friends 1 to 3 of 3
No results to show...