Tab Content
  • dan7777's Avatar
    3 Days Ago
    dan7777 replied to a thread [Electrical] IRAdvC5250 - Main controller pcb2 in Canon
    I would try it. Any small pcb on boards from the one in the machine should go on new board. Do a dc con back up and when you put in new board do a...
    3 replies | 125 view(s)
  • dan7777's Avatar
    3 Days Ago
    dan7777 replied to a thread E027-0400 AdvC5035 in Canon
    I have had to clean drum encoders in back and had a drum blade flip only once. Replaced drum for blade flip.
    4 replies | 146 view(s)
  • dan7777's Avatar
    4 Days Ago
    I have a lot of these machines. After a while the gears wear off. The 50xx have couplings in the back that fail. New style coupler has a pin in it...
    2 replies | 113 view(s)
  • dan7777's Avatar
    5 Days Ago
    dan7777 replied to a thread Canon 3300 part # needed in Canon
    4 replies | 217 view(s)
  • dan7777's Avatar
    5 Days Ago
    dan7777 replied to a thread Canon 3300 part # needed in Canon
    There are metal springs that sometimes break and the lift gear breaks a tooth. I used to replace the entire feed assembly to fix some of those as...
    4 replies | 217 view(s)
  • ernesto's Avatar
    1 Week Ago
    ernesto started a thread IRC 1325i in Canon
    Hi I have an IR C1325i asking for toner magenta but it has. Does anyone know the problem? I look forward to hearing from you soon All the...
    0 replies | 139 view(s)
  • dan7777's Avatar
    1 Week Ago
    Two things can cause this. One is in the fuser, full page color on 7265. We have only found setting the lead edge blanking to fix this. The other is...
    6 replies | 392 view(s)
  • dan7777's Avatar
    1 Week Ago
    dan7777 replied to a thread [Jamming] duplex jam samsung 8240nd in Samsung
    I had one like this. I don't have a Samsung like this one I had so don't remember the model number. There was a clutch in behind the fuser. Had to...
    4 replies | 112 view(s)
  • dan7777's Avatar
    1 Week Ago
    Anyone replace registration clutch before? I was able to get assembly loose but could not pull it away. No instructions I could find. Looks like...
    1 replies | 72 view(s)
  • dan7777's Avatar
    2 Weeks Ago
    dan7777 replied to a thread e0733 code... in Canon
    Only saw one post in knowledge base and that was for engine controller which is also called the dc controller you replaced. Make sure you do a backup...
    1 replies | 168 view(s)
  • dan7777's Avatar
    2 Weeks Ago
    dan7777 replied to a thread [Misc] Toner irc4580 > adv5030 in Canon
    Only if you like playing Russian roulette.
    4 replies | 325 view(s)
  • dan7777's Avatar
    3 Weeks Ago
    Those files are too big to send email. Sometimes people are nice enough to post them to sites you have to register on. Only Samsung dealers have...
    3 replies | 168 view(s)
  • dan7777's Avatar
    3 Weeks Ago
    They seem to do that with the names. DC controller in parts and Engine controller in service manual. Just had a different problem with a 4545 and...
    1 replies | 115 view(s)
  • dan7777's Avatar
    3 Weeks Ago
    dan7777 replied to a thread Samsung machines in Samsung
    We did not have good luck and sales people started not selling them as pricing got higher. We were purchased by very large company and they said the...
    2 replies | 177 view(s)
  • dan7777's Avatar
    3 Weeks Ago
    dan7777 replied to a thread ir5055 half light in Canon
    Luckily I only have one or two of those left and rarely see them. When I first looked at it looked like something on laser glass but if it is...
    9 replies | 317 view(s)
  • dan7777's Avatar
    3 Weeks Ago
    dan7777 replied to a thread [Misc] a 'quick' firmware naming question in Canon
    I use usb 80% of the time because I think it is faster. If it were me I would go ahead and download what the latest updater was. Or install with sst...
    5 replies | 167 view(s)
  • dan7777's Avatar
    3 Weeks Ago
    dan7777 replied to a thread [Misc] IR C5045, C9075 - life and reliability? in Canon
    Expected reliable life of copiers has always been 3-5 years. Make your service guy happy and buy new machines.
    2 replies | 136 view(s)
  • ernesto's Avatar
    3 Weeks Ago
    ernesto started a thread ir advance 400 i in Canon
    There is no edge blank in the copies or page impressions Solution: replacing register clutch
    0 replies | 77 view(s)
  • dan7777's Avatar
    3 Weeks Ago
    dan7777 replied to a thread [Misc] a 'quick' firmware naming question in Canon
    It seems like that is only 6 months or so old. You have a box with different languages but I use the drop down list to update (above the different...
    5 replies | 167 view(s)
  • dan7777's Avatar
    3 Weeks Ago
    dan7777 replied to a thread [Misc] a 'quick' firmware naming question in Canon
    That was funny! I think you may have been right. This was in my irca2030 folder "SYSTEM_4601-JEFIGS-DCON_6705". I think you can have several versions...
    5 replies | 167 view(s)
  • dan7777's Avatar
    3 Weeks Ago
    dan7777 replied to a thread AdvC5035 duplex on a MAC in Canon
    Yes I think this is how you do this. We had a C250 with the same issue. If this way does not work google CUPS and they will tell you what to do....
    7 replies | 211 view(s)
  • ernesto's Avatar
    3 Weeks Ago
    are there two boards in this machine, one board work with yelow and black y the other board work with cyan and magenta???? if the answer is yes can...
    2 replies | 267 view(s)
  • ernesto's Avatar
    3 Weeks Ago
    ernesto started a thread irc1325i in Canon
    HI I have a problem with a irc1325i there are color and black and white lines everywhere it seems that the itb does not work but I replaced the...
    0 replies | 57 view(s)
No More Results
About dan7777

Basic Information

Date of Birth
March 25, 1952 (65)
About dan7777
Real Name:
Dan Schorr
Country:
United States
State/County:
us tennessee
Where are you from (City, State):
Bristol
Biography:
27 years technician
Interests:
bible, computer
What Year Did You Start in this Industry:
1985
Most Hated Brand:
Mita
What was the first machine you worked on:
minolta
Last machine you were formally trained on:
Ricoh
Gender:
Male

Statistics


Total Posts
Total Posts
505
Posts Per Day
0.29
General Information
Last Activity
3 Hours Ago
Join Date
12-17-2012
Referrals
0

2 Friends

  1. ernesto ernesto is offline

    Senior Tech

    ernesto
  2. nancy nancy is offline

    Junior Member

    nancy
Showing Friends 1 to 2 of 2

10-23-2017


10-19-2017


10-13-2017


10-06-2017