Tab Content
  • dan7777's Avatar
    2 Days Ago
    dan7777 replied to a thread Canon IRC3330i E302-0001 in Canon
    Try scanner ribbon cable first but in my case code came back and I replaced scanner also.
    2 replies | 88 view(s)
  • cucuklotz's Avatar
    5 Days Ago
    cucuklotz replied to a thread Xerox Workcentre 7225 in Xerox
    Thank you Phil B again for replying.I tried to find Altboot for 7225,but could not find,I have tried many searches.I have found Altboots procedures...
    4 replies | 185 view(s)
  • dan7777's Avatar
    5 Days Ago
    dan7777 replied to a thread [Error Code] CAON IRADVC5250i Error E0029-003 in Canon
    Check fuse FU2 on paper feed driver PCB.
    4 replies | 169 view(s)
  • cucuklotz's Avatar
    1 Week Ago
    cucuklotz replied to a thread Xerox Workcentre 7225 in Xerox
    Hi Thank you for replying.Il let you know how it works out. ...
    4 replies | 185 view(s)
  • cucuklotz's Avatar
    1 Week Ago
    cucuklotz started a thread Xerox Workcentre 7225 in Xerox
    Hi After powering up the WC7225,the machine never boots up.The green energy save button stays lite,and nothing else happens. No display or...
    4 replies | 185 view(s)
  • dan7777's Avatar
    1 Week Ago
    No it shows. iR 8500/105/7200/85.- iR 9070/105+/8070/85+
    7 replies | 249 view(s)
  • dan7777's Avatar
    1 Week Ago
    . Off the canon dealer website. It only uses the service support tool. I do not even mess with trying to get someone a file that big, sorry. I do...
    7 replies | 249 view(s)
  • dan7777's Avatar
    1 Week Ago
    You may have a hard time getting that. It shows 222Meg last version in Sept. 2008.
    7 replies | 249 view(s)
  • dan7777's Avatar
    1 Week Ago
    Check all the pages. Maybe someone moved it to another page. We move the scanner, ifax and others to pages you can not see. If it is not anywhere...
    4 replies | 200 view(s)
  • dan7777's Avatar
    1 Week Ago
    dan7777 replied to a thread CANON IR ADV c 7055 in Canon
    If you pull the magenta developer out and see those voids on the mag roller then problem is in developer. That is one developer you can take the dr....
    5 replies | 296 view(s)
  • dan7777's Avatar
    2 Weeks Ago
    dan7777 replied to a thread [Error Code] E020-391 IR5030i in Canon
    Very common. If you have the plus gear with pin then look at the part that drives it. It is a toss up weather to take out the drive assembly and...
    15 replies | 650 view(s)
  • dan7777's Avatar
    2 Weeks Ago
    dan7777 replied to a thread Canon Advance IRC2230 jams in Canon
    Glad you found the repair. On the newer models you can touch the jam code and it tells you sensor (with picture) and if delay or stationary. On error...
    8 replies | 348 view(s)
  • dan7777's Avatar
    2 Weeks Ago
    dan7777 replied to a thread Canon Advance IRC2230 jams in Canon
    Funny, I have one this morning jamming in the 2/3 delivery. 020B. 0205 is delay at reg flag. I had to replace that flag assembly on one of them. It...
    8 replies | 348 view(s)
  • dan7777's Avatar
    2 Weeks Ago
    dan7777 replied to a thread [CQ] IR C350 faded copies in Canon
    I go by percentage and mine get 80-120% before they go light with canon drums. I am going to guess that is 20-30 thousand copies.
    3 replies | 146 view(s)
  • dan7777's Avatar
    3 Weeks Ago
    dan7777 replied to a thread Canon Advance IRC2230 jams in Canon
    When you put in a fuser you have to take two screws off and put the assembly off old fuser on the new fuser. Those bushings get knocked out of place...
    8 replies | 348 view(s)
  • dan7777's Avatar
    3 Weeks Ago
    dan7777 replied to a thread Canon Advance IRC2230 jams in Canon
    When you put in a fuser you have to take two screws off and put the assembly off old fuser on the new fuser. Those bushings get knocked out of place...
    8 replies | 348 view(s)
  • dan7777's Avatar
    3 Weeks Ago
    Almost forgot. The hinges have been updated and I put in new hinges also. I think they were updated for that reason. It would feed from both right...
    3 replies | 175 view(s)
  • dan7777's Avatar
    3 Weeks Ago
    I did on a 6XXX series. It was the right door. Either warped or worn (the guides). I think canon had a update on a piece in the middle. It was on a...
    3 replies | 175 view(s)
  • cucuklotz's Avatar
    3 Weeks Ago
    THANK YOU SANDMANMAC I spoke to the customer after I saw your reply,I know their computer guy so I passed...
    3 replies | 145 view(s)
  • cucuklotz's Avatar
    3 Weeks Ago
    Hi When I searched code online I saw that it could be network related on many Ricohs,But did not see anything specifically on the 4310. Has...
    3 replies | 145 view(s)
No More Results
About dan7777

Basic Information

Date of Birth
March 25, 1952 (66)
About dan7777
Real Name:
Dan Schorr
Country:
United States
State/County:
us tennessee
Where are you from (City, State):
Bristol
Biography:
31 years technician
Interests:
bible, computer
Occupation:
Technician
What Year Did You Start in this Industry:
1985
Most Hated Brand:
Mita
What was the first machine you worked on:
minolta
Last machine you were formally trained on:
Ricoh
Gender:
Male

Statistics


Total Posts
Total Posts
611
Posts Per Day
0.29
General Information
Last Activity
2 Days Ago
Join Date
12-17-2012
Referrals
0

3 Friends

  1. cucuklotz cucuklotz is offline

    Field Supervisor

    cucuklotz
  2. ernesto ernesto is offline

    Senior Tech

    ernesto
  3. nancy nancy is offline

    Junior Member

    nancy
Showing Friends 1 to 3 of 3

09-18-2018


09-12-2018


09-10-2018


09-01-2018