Tab Content
  • teckat's Avatar
    7 Hours Ago
    teckat replied to a thread [Jamming] Ir6000 in Canon
    Welcome 🍺
    5 replies | 391 view(s)
  • teckat's Avatar
    1 Day Ago
    How many times have you replaced the fix roller_? or replaced swollen heat lamp_? Canon NP-1010/1020 Copier Drum Unit (20000 Page Yield)...
    3 replies | 105 view(s)
  • teckat's Avatar
    2 Days Ago
    You were supposed to do the Boot first , when doing get 60 or newer. Check and reseat connector J318 on the Image Processor and connector J1701 on...
    30 replies | 18579 view(s)
  • teckat's Avatar
    2 Days Ago
    so this does not work--:( To put the unit into download mode start with the power off. Press and hold the 2 key only on the ten key pad and then...
    30 replies | 18579 view(s)
  • teckat's Avatar
    3 Days Ago
    Make sure RUI in turned on in Additional Functions>System Settings>Remote UI>ON In Service Mode, to disable the password request for RUI. ...
    1 replies | 116 view(s)
  • teckat's Avatar
    3 Days Ago
    teckat replied to a thread [Jamming] Ir6000 in Canon
    https://www.dropbox.com/s/dlx0mjb66h92w4m/finisher-v1-sm.pdf?dl=0
    5 replies | 391 view(s)
  • teckat's Avatar
    3 Days Ago
    printer has no internet connection :confused: It will be necessary to ensure that the correct Country / Area selection in service mode is correct...
    14 replies | 656 view(s)
  • teckat's Avatar
    3 Days Ago
    teckat replied to a thread [Jamming] Ir6000 in Canon
    check supply voltage & connectors from 0107 issue machine to unit & driver pcb :confused: Right deck pickup motor M11 J104-DC controller PCB...
    5 replies | 391 view(s)
  • teckat's Avatar
    4 Days Ago
    if all glass copies are good :confused: & all internal test prints are good :confused: u could try a firmware update if needed or overwrite...
    14 replies | 656 view(s)
  • teckat's Avatar
    4 Days Ago
    teckat replied to a thread service support tool in Canon
    is message on all drums ? or just black ?? did u check those interior white couplings ?
    29 replies | 4417 view(s)
  • teckat's Avatar
    4 Days Ago
    so in process of elimination :p re-loaded drivers = same issue tested from 3 different computers= same issue u have an internal image...
    14 replies | 656 view(s)
  • teckat's Avatar
    4 Days Ago
    teckat replied to a thread service support tool in Canon
    DCON v49.01 was introduced to Help Prevent Miscellaneous "Insert Drum Cartridge" Messages in year 2009 Information on a way to help prevent...
    29 replies | 4417 view(s)
  • teckat's Avatar
    4 Days Ago
    teckat replied to a thread service support tool in Canon
    Machine is displaying a message to "Insert Drum Cartridge" for black even after a new drum has been installed.:confused: The problem could be...
    29 replies | 4417 view(s)
  • teckat's Avatar
    4 Days Ago
    hook up a laptop and send over some prints to check ? so anything you send from your PC to print on 8105 has this issue ??
    14 replies | 656 view(s)
  • teckat's Avatar
    5 Days Ago
    Remove those drivers completely. Re install from here-- imageRUNNER ADVANCE 8105 PRO Support - Download Drivers, Software & Manuals
    14 replies | 656 view(s)
  • teckat's Avatar
    6 Days Ago
    teckat replied to a thread [Misc] Canon IR 3570 Printing very light in Canon
    Have u stopped the print half way to inspect image on DRUM SURFACE?
    10 replies | 489 view(s)
  • teckat's Avatar
    6 Days Ago
    teckat replied to a thread [Misc] Canon IR 3570 Printing very light in Canon
    Transfer method =by transfer roller= transfers images from the drum to paper=bias voltage applied to the transfer roller causes the toner to move...
    10 replies | 489 view(s)
  • teckat's Avatar
    1 Week Ago
    teckat replied to a thread Error Code E000110-0436 in Canon
    _________________________________see Laser Scanner Motor Trouble E110 sub codes descriptions are as follows: 1st line: Always 0 2nd...
    2 replies | 201 view(s)
  • teckat's Avatar
    1 Week Ago
    teckat replied to a thread [Misc] Canon IR 3570 Printing very light in Canon
    Transfer method = by transfer roller= transfers images from the drum to paper=bias voltage applied to the transfer roller causes the toner to move...
    10 replies | 489 view(s)
  • teckat's Avatar
    1 Week Ago
    teckat replied to a thread [Misc] Canon IR 3570 Printing very light in Canon
    Inspect & Reseat transfer roller and confirm correct pressure. Check the front and rear transfer arms for proper positioning. When positioned...
    10 replies | 489 view(s)
  • teckat's Avatar
    1 Week Ago
    teckat replied to a thread C3480 Error 852 in Canon
    ______is a Fax board installed ? Yeah, those side pcbs need to be removed and ends cleaned. Then re seated straight and level. Also check...
    3 replies | 139 view(s)
  • teckat's Avatar
    1 Week Ago
    There is an option called 'Long Strip Original' that will automatically rotate the scanned originals during the scanning process when push scanning...
    7 replies | 208 view(s)
  • teckat's Avatar
    1 Week Ago
    Service mode setting Scan -SLCT > set to 1. Also> Check in service mode that the Long Document Sensor for the DADF is changing state. It's...
    7 replies | 208 view(s)
  • teckat's Avatar
    1 Week Ago
    teckat replied to a thread C3480 Error 852 in Canon
    Is this with PDF's only ? Turn off spooler on the printer, ADDITIONAL FUNCTION > SYSTEM SETTINGS > NETWORK SETTINGS > USER SPOOLER,...
    3 replies | 139 view(s)
  • teckat's Avatar
    1 Week Ago
    E520 0001 = Shift Motor fails to move from HP At initial rotation, when the Motor rotates for specified period of time and cannot move from HP, it...
    2 replies | 224 view(s)
  • teckat's Avatar
    1 Week Ago
    teckat replied to a thread E00227 in canon ir 2870 in Canon
    E227 == reader unit power supply error 0001 At time of power-on, the 24-V port is off. Disconnect and then connect the power supply harness...
    1 replies | 190 view(s)
  • teckat's Avatar
    1 Week Ago
    imageRUNNER 7105 The quickest way to troubleshoot a 0094 is to use the FEEDER IO section found in service mode. COPIER>IO>FEEDER. The sensors...
    10 replies | 9266 view(s)
  • teckat's Avatar
    1 Week Ago
    C800/C700/C600 lets you quicklyand effortlessly produce duplex print jobs on heavy weight media up to 300 gsm, Compact Registration Module delivers...
    4 replies | 397 view(s)
  • teckat's Avatar
    1 Week Ago
    teckat replied to a thread Canon IR2520 Start up in Canon
    best to stay out of service mode if u have no working knowledge on product :rolleyes: describe your CQ issue----:confused:
    13 replies | 13006 view(s)
  • teckat's Avatar
    1 Week Ago
    imageRUNNER 2270 / 2870 / 3570 /4570 With system software version 32.01 and higher Remote Operator’s Software Kit-A1 is supported. This option...
    8 replies | 238 view(s)
More Activity
About fatove

Basic Information

About fatove
Real Name:
Frank
Country:
Ghana
Where are you from (City, State):
Tema
Biography:
I am a young man
Interests:
internet
What Year Did You Start in this Industry:
3
What was the first machine you worked on:
Computer
Last machine you were formally trained on:
copier
Gender:
Male

Statistics


Total Posts
Total Posts
3
Posts Per Day
0.00
General Information
Last Activity
10-08-2011
Join Date
09-30-2011
Referrals
0

1 Friend

  1. teckat teckat is offline

    Field Supervisor

    teckat
Showing Friends 1 to 1 of 1
No results to show...