Tab Content
  • Gab's Avatar
    13 Hours Ago
    Toner , drum and developer OEM. I eecuted forced toner and image was the same. I believe it's the voltage that attracts toner to paper . Can anybody...
    9 replies | 218 view(s)
  • Gab's Avatar
    19 Hours Ago
    A capacitor blew up at power supply , I fixed power sypply and an erro 6030 appeared . This error is about thermistor . Can it be something else...
    3 replies | 127 view(s)
  • Gab's Avatar
    1 Day Ago
    Copies (and printings ) from MP 2501 are light. Drum and developer are new (about 2k copies) . |Is there any way to make them darker?
    9 replies | 218 view(s)
  • Gab's Avatar
    3 Days Ago
    Peper stops just as paper exits . I know that usually this happens when wrong paper is at paper cassete. It doesn't happens here. I have noticed...
    13 replies | 849 view(s)
  • Gab's Avatar
    3 Days Ago
    paper jam when paper just exits(It exits about 1cmm and stop). Also some times double feed occurs. It happens when using both paper cassetes. The...
    13 replies | 849 view(s)
  • Gab's Avatar
    6 Days Ago
    MAchine is ΜΡ 2501 , Ι have cleaned laser unit and polygon mirror surfaces . As i have told you the problem started after first maintence . at that...
    6 replies | 336 view(s)
  • Gab's Avatar
    1 Week Ago
    Gab replied to a thread biz 282 in Konica Minolta
    \ As i havw reten , i folloew service manual instructions . So i cleared PC life and developer counters , turned of machine , replaced opc and...
    15 replies | 853 view(s)
  • Gab's Avatar
    1 Week Ago
    Gab replied to a thread biz 282 in Konica Minolta
    I doubt you can run an F8 with an existing c2557 code, so I assume you are hitting the reset switch, pressing 3, entering 00000000, trouble reset,...
    15 replies | 853 view(s)
  • Gab's Avatar
    1 Week Ago
    A capasitor on power supply board blew up and also the board cracked. caN ANYBODY TELL ME IF power suplly board oa olivetti 253 is exactly the same...
    1 replies | 164 view(s)
  • Gab's Avatar
    1 Week Ago
    In the first maintance of this machine i replaced opc , blade and developer but instand of executing 2 801 i executed 2 802. Ever since i couldn't...
    6 replies | 336 view(s)
  • Gab's Avatar
    1 Week Ago
    Gab replied to a thread biz 282 in Konica Minolta
    I cleared counters PC life and developer then i replaced developer again and executed F8. When F8 finished error 255c appered turned on and of...
    15 replies | 853 view(s)
  • Gab's Avatar
    1 Week Ago
    Gab replied to a thread biz 282 in Konica Minolta
    If i replace again developer clear PClife (do i have to clear developer too?) replace developer and execute F8 will error 2557 dissapear? Is there...
    15 replies | 853 view(s)
  • Gab's Avatar
    3 Weeks Ago
    Gab replied to a thread biz 282 in Konica Minolta
    I checked and fixed toner solenoid but the same When error 2557 appers i must clear again PC life and developer in order to deisapper error 2557....
    15 replies | 853 view(s)
  • Gab's Avatar
    3 Weeks Ago
    Gab replied to a thread biz 282 in Konica Minolta
    I checked atdc sensor value and it was 177 . I changed it to 185 with no result. cleared again pc life and developer counters turned off and on...
    15 replies | 853 view(s)
  • Gab's Avatar
    3 Weeks Ago
    Gab started a thread biz 282 in Konica Minolta
    Message M4 for maintence appeared . I cleared PC life replaced opc and developer and from special parts, counter cleared all counters. I|n order to...
    15 replies | 853 view(s)
  • Gab's Avatar
    3 Weeks Ago
    Paper jam occurs frequenrly at fusing. Paper jam one of upper picker fingers I replaced hot, upper piocker finger with no result . I note that...
    5 replies | 408 view(s)
No More Results
About Gab

Basic Information

About Gab
Real Name:
Gabriel
Country:
Greece
Where are you from (City, State):
Alexandroupolis, evros
Biography:
I am in the field for about 20 years. I am a Ricoh tech but i am interested in that period for Kyocera machines .Also Konica minolata machines interests me.
Interests:
Basketball, Fishing
What Year Did You Start in this Industry:
1994
Most Hated Brand:
Xerox
What was the first machine you worked on:
canon NP1550
Last machine you were formally trained on:
Aficio mp2501
Gender:
Male

Statistics


Total Posts
Total Posts
185
Posts Per Day
0.19
General Information
Last Activity
4 Hours Ago
Join Date
08-23-2015
Referrals
0
No results to show...