Tab Content
  • Gina82's Avatar
    5 Days Ago
    Gina82 replied to a thread Riso RN2030UI in Digital Duplicators
    I have replaced the compression plate sensor and motor connected to it as well and now the compression plate will not come out of a downward...
    5 replies | 252 view(s)
  • Gina82's Avatar
    5 Days Ago
    Gina82 replied to a thread Bizhub 361 in Konica Minolta
    I'll give it a try
    13 replies | 412 view(s)
  • Gina82's Avatar
    6 Days Ago
    Gina82 replied to a thread Bizhub 361 in Konica Minolta
    Attempted to set up FTP server but copier would not show up on filezilla server interface. Turned on SMB 1.0 and attempted to scan to smb but that...
    13 replies | 412 view(s)
  • Gina82's Avatar
    6 Days Ago
    Gina82 replied to a thread C284e in Konica Minolta
    So I swapped the staple cartridges around as suggested first. This seems to have fixed my problem. I have checked on this machine twice since then...
    7 replies | 456 view(s)
  • Gina82's Avatar
    6 Days Ago
    Gina82 replied to a thread Bizhub 361 in Konica Minolta
    I see that the driver is supported, but my issue is with the scan to smb process. Whenever I set it up with a PC using the windows 10 operating...
    13 replies | 412 view(s)
  • Gina82's Avatar
    6 Days Ago
    Gina82 replied to a thread [Electrical] M6026CDN asking for cyan toner in Kyocera Mita, Copystar
    Check auger in transfer belt that is responsible for adding toner. These tend to break (plastic). In my experience, ours usually start with asking...
    5 replies | 233 view(s)
  • Gina82's Avatar
    1 Week Ago
    Gina82 started a thread Bizhub 361 in Konica Minolta
    Does anyone know the operating systems that are compatible with a bizhub 361, or know where I can find a list that will tell me?
    13 replies | 412 view(s)
  • Gina82's Avatar
    2 Weeks Ago
    Gina82 replied to a thread Riso RN2030UI in Digital Duplicators
    I think the issue may be caused by the master compression sensor . The compression plate never turns to dump the compressed master into the master...
    5 replies | 252 view(s)
  • Gina82's Avatar
    2 Weeks Ago
    I have a Riso RN2030UI that gives me an A34-218, the service manual doesn't really help much on the issue. When making the master for a print job the...
    5 replies | 252 view(s)
  • Gina82's Avatar
    2 Weeks Ago
    Gina82 replied to a thread C284e in Konica Minolta
    At this point, I honestly wouldn't be surprised if it was lol
    7 replies | 456 view(s)
  • Gina82's Avatar
    2 Weeks Ago
    Gina82 replied to a thread C284e in Konica Minolta
    Went to check the machine today and attempt to swap staple cartridges but the machine was fully functional. This happened before though, we replaced...
    7 replies | 456 view(s)
  • Gina82's Avatar
    2 Weeks Ago
    Gina82 started a thread C284e in Konica Minolta
    I have a C284e that has SD-511 in the finisher. My problem is when paper reaches finisher to be center folded and stapled, the first saddle staple...
    7 replies | 456 view(s)
No More Results
About Gina82

Basic Information

About Gina82
Real Name:
Regina Champion
Country:
United States
Where are you from (City, State):
Greenwood, MS
What Year Did You Start in this Industry:
2006
Gender:
Female

Statistics


Total Posts
Total Posts
33
Posts Per Day
0.07
General Information
Last Activity
3 Days Ago
Join Date
10-31-2017
Referrals
1

03-14-2019


03-13-2019