Tab Content
  • Lance15's Avatar
    1 Day Ago
    Lance15 replied to a thread LJ4250 with 13.02 errors in HP
    I started using the command strips, then, I bought a roll of double sided velcro (the "fuzzy" side only) from Amazon, but, electrical tape works too....
    16 replies | 771 view(s)
  • Lance15's Avatar
    2 Days Ago
    Lance15 replied to a thread [Error Code] DesignJet 500 in HP
    81:01 Problem Description: Paper-Axis shutdown. Corrective Action: If this error code appeared but was not caused by a paper jam, then try the...
    7 replies | 1229 view(s)
  • Lance15's Avatar
    2 Days Ago
    From what I've typically seen, these are the culprit: Q1273-60245 - ISS to Cartridge Cable The first time I replaced one, I didn't think it was...
    4 replies | 205 view(s)
  • Lance15's Avatar
    6 Days Ago
    Lance15 replied to a thread LJ4250 with 13.02 errors in HP
    I usually make that part of "the works". Fuser Swing Plate Rollers Clean the now sticky foam pads off of the registration assembly & exit bin...
    16 replies | 771 view(s)
  • Lance15's Avatar
    1 Week Ago
    Looking at the LQ-2170 service manual (disassembly is the same as the 2180). I see this printer uses several optical sensors to detect things: PW...
    4 replies | 228 view(s)
  • Lance15's Avatar
    1 Week Ago
    Maybe the encoder strip needs to be cleaned? The encoder strip tells the carriage "where it's at". If it's dirty, the sensor in the carriage can't...
    4 replies | 228 view(s)
  • Lance15's Avatar
    2 Weeks Ago
    Lance15 replied to a thread Part number HP CLJ 3700 in HP
    Ohhhhh yeah. I think I know what your talking about. I think the only time I was able to replace that gear was when the customer had a 3700 that...
    5 replies | 413 view(s)
  • Lance15's Avatar
    2 Weeks Ago
    Lance15 replied to a thread [Dead] hp service in HP
    Sounds like the heating element is shot. Replace the whole fuser assembly.
    7 replies | 471 view(s)
  • Lance15's Avatar
    3 Weeks Ago
    Lance15 replied to a thread LJ4250 with 13.02 errors in HP
    More than likely, yes, the solenoid needs to be re-padded.
    16 replies | 771 view(s)
  • Lance15's Avatar
    3 Weeks Ago
    Time for either a replacement formatter or bake the current one. I've done it a couple of times. Works great. Reflows the solder.
    4 replies | 189 view(s)
  • Lance15's Avatar
    3 Weeks Ago
    Pickup assembly. Just did one of these a couple of weeks ago. In my case, it turned out a piece of plastic that held a spring in place inside the...
    3 replies | 308 view(s)
  • Lance15's Avatar
    4 Weeks Ago
    Lance15 replied to a thread [Jamming] 13.a2.d2 hp4555 in HP
    I think I seem to remember this or similar code on an M880. That turned out to be bad paper in the tray.
    4 replies | 351 view(s)
  • Lance15's Avatar
    4 Weeks Ago
    Lance15 replied to a thread HP Design jet Z2100 44" in HP
    There is a print job sitting on either a print server or someone's PC that is trying to print once the plotter is connected to the network. The...
    1 replies | 187 view(s)
  • Lance15's Avatar
    4 Weeks Ago
    Lance15 replied to a thread Scitex FB550 Printheads in HP
    OH MY.......!!!!!! Sorry Kiran. I only buy PLOTTER parts mainly from HP. I hope NONE of our customers gets one of THESE beasts! Is this one...
    5 replies | 392 view(s)
  • Lance15's Avatar
    4 Weeks Ago
    Lance15 replied to a thread [Error Code] HP CP3525n getting 59.F0 in HP
    I get SOOOOOOOOOOO lucky with a customer that has a bunch of the CP4525's that have been slowly coding this error and they want them fixed. Lucky...
    3 replies | 289 view(s)
  • Lance15's Avatar
    4 Weeks Ago
    Lance15 replied to a thread [Jamming] 13.a2.d2 hp4555 in HP
    Hmmmmmm. Typically this error is a bad paper pickup assembly. Had an M651 coding with similar/same code. Found a broken part on the paper pickup...
    4 replies | 351 view(s)
No More Results
About Lance15

Basic Information

About Lance15
Real Name:
Lance Gentle
Country:
United States
State/County:
us maryland
Where are you from (City, State):
Lutherville, MD
Gender:
Undisclosed

Statistics


Total Posts
Total Posts
363
Posts Per Day
0.41
General Information
Last Activity
15 Hours Ago
Join Date
06-30-2015
Referrals
0

11-08-2017


11-06-2017


11-02-2017


10-27-2017


10-25-2017