View Profile: PrintHub - Copytechnet.com

3 Days Ago

allan replied to a thread can I use a FS-539 SD finisher with a bizhub 958? in Konica Minolta

I would suggest to not let it do firmware with the finisher attached. It could work like the FS534 working instead of the FS536 on the 8 series but ...

6 replies | 465 view(s)

3 Days Ago

allan replied to a thread [Misc] KM Acount Track in Konica Minolta

You need to setup user authentication for all the individual users regardless of the department. Then setup account track for the departments. The...

4 replies | 552 view(s)

3 Days Ago

allan replied to a thread Developer in toner in Konica Minolta

You have got me curious. What are you trying to do? The devtank will discard excess developer through the waste port. I would guess about a teaspoon...

9 replies | 768 view(s)

3 Days Ago

allan replied to a thread can I use a FS-539 SD finisher with a bizhub 958? in Konica Minolta

+1 Only FS-536/537 as per configuration. But.... https://www.scribd.com/document/336996567/Bizhub-958-808-758-Spec-Sheet-En

6 replies | 465 view(s)

4 Days Ago

allan replied to a thread RADF Separation Roller, modified in Konica Minolta

Its a trick to get them on there but the hared blue AA2J560000 rollers last forever. Been using them on the 4 series paper feed separation and the...

4 replies | 312 view(s)

1 Week Ago

allan replied to a thread FS-537 with C-1132 in Konica Minolta

Make sure that the connectors between the punch and FSCB are seated properly. Had badly seated connectors causing this code before.

4 replies | 641 view(s)

1 Week Ago

allan replied to a thread how to change the count of an A3 sheet in Konica Minolta

Hi please post the meter counter page to check the setting.

10 replies | 952 view(s)

1 Week Ago

allan replied to a thread how to change the count of an A3 sheet in Konica Minolta

+1. Someone is getting screwed over. I have been asked this from dodgy end-users before.

10 replies | 952 view(s)

2 Weeks Ago

allan replied to a thread Marketplace and Google Connector. in Konica Minolta

Think there is something wrong with that link.

12 replies | 905 view(s)

2 Weeks Ago

allan replied to a thread what's your opinion on surge protection in Copier Technical Discussion

Look for locally for any surge protector plugs that includes Ethernet surge(Network surge) protection. Or phone a Konica Minolta, Kyocera, or RICOH...

13 replies | 1014 view(s)

2 Weeks Ago

allan replied to a thread [Error Code] C300i , code C 9401 in Konica Minolta

Have you check the small timing belt on the motor for damage?

8 replies | 3914 view(s)

2 Weeks Ago

allan replied to a thread Marketplace and Google Connector. in Konica Minolta

Here goes the first one for me. Looks like I could have a problem buying it locally from KMSA. The ZA shop does not show any pricing. Useless... ...

12 replies | 905 view(s)

2 Weeks Ago

allan replied to a thread what's your opinion on surge protection in Copier Technical Discussion

Clearline is a brand I trust. NOt sure if they are limited to ZA. They are all build with the same basic components so it depends on reputation....

13 replies | 1014 view(s)

2 Weeks Ago

allan replied to a thread Marketplace and Google Connector. in Konica Minolta

Ok silly I am... Figured it out but wow yea for a site selling UI's the UI sucks a bit. Sure I will get stuck somewhere else again. Anyway...

12 replies | 905 view(s)

2 Weeks Ago

allan started a thread Marketplace and Google Connector. in Konica Minolta

I am new to all this but managed to get google connector working, kind of. Its a trail version and does not stay logged in to the google account but...

12 replies | 905 view(s)

3 Weeks Ago

allan replied to a thread C-450i accordian jam at fuser entrance , J-3003 code in Konica Minolta

Check if the registration sensor flag is not stuck or use sensor check in service mode. Is there any image on the page and registered correctly?

6 replies | 571 view(s)

3 Weeks Ago

allan replied to a thread BH-C-284e, offsetting, would love to have an explanation in Konica Minolta

Yea that is strange. All I can think of is that there could be a latent charge form the yellow and cyan toner on the transfer belt. The black is...

10 replies | 810 view(s)

3 Weeks Ago

allan replied to a thread C458 with strips in Konica Minolta

It looks like the edge of the page. I am familiar with the internal printout. It looks like soiling more than lines to me. Would be better if the OP...

12 replies | 1076 view(s)

3 Weeks Ago

allan replied to a thread Minolta c452 Gear Help in Konica Minolta

This is where 3D printed gears would be handy.

6 replies | 522 view(s)

3 Weeks Ago

allan replied to a thread C458 with strips in Konica Minolta

How is the condition of your fuser sleeve and pressure roller?

12 replies | 1076 view(s)

3 Weeks Ago

allan replied to a thread Linux driver for print and scan function in Konica Minolta

Just had some customers upgrade there Linux mint that caused the smb to fail.Had not been able to resolve the issue yet. Try to enable SMB v1 using...

9 replies | 1318 view(s)

3 Weeks Ago

allan replied to a thread Linux driver for print and scan function in Konica Minolta

The SMB version on your machine could be outdated. What model of machine and what Linux distro? With the 4 series machines I use filezilla FTP for...

9 replies | 1318 view(s)

3 Weeks Ago

allan replied to a thread bizhub 227 prints lines in Konica Minolta

There is a high voltage leakage between the drum unit and the devtank. Sure you can feel the developer on the paper? Any scratches on the drum...

4 replies | 478 view(s)

3 Weeks Ago

allan replied to a thread C224e strange message in Konica Minolta

Agree that the NVRAM battery is bad. Check under trouble isolation it the fax option is set if so unset it.

5 replies | 408 view(s)

PrintHub
Technician

Mini Statistics

More 1 Friend

allan

Recent Visitors

Basic Information

About PrintHub

Statistics

Total Posts

General Information

1 Friend

allan

PrintHub Technician

Mini Statistics

More 1 Friend

allan

Recent Visitors

Basic Information

About PrintHub

Statistics

Total Posts

General Information

1 Friend

allan

PrintHub
Technician