-
Older Activity
-
2 Hours Ago
Determine which drum fits too tightly on it's drum shaft. In my case it was 3 out of 4. Install only one drum, then close the drawer to see if it...
5 replies | 2700 view(s)
-
1 Day Ago
Could it be that it had a Lexmark toner cartridge installed, not a Toshiba cartridge? Or vice-versa? I'd think the EEPROM would be coded differently....
13 replies | 569 view(s)
-
1 Day Ago
There certainly isn't a lot of detail in that bulletin. It would have been nice to know what changed. Or would that be too much like admitting there...
5 replies | 406 view(s)
-
1 Day Ago
Your welcome. Sorry I missed your post on the first go-round. =^..^=
9 replies | 1048 view(s)
-
2 Days Ago
The cyan & magenta developing units are the only thing it needs..
Yes, I reduced the resolution on my camera phone so that the pictures were 1MB...
15 replies | 800 view(s)
-
2 Days Ago
Sorry, no DIY fix. Those developing units are glued together. I have tried disassembling a few units, but just ended up with broken plastic. The...
15 replies | 800 view(s)
-
2 Days Ago
The cyan and magenta developing spacers are bad. AFAIK the only way to get them is on a whole developing unit assembly. This was a common flaw on...
15 replies | 800 view(s)
-
2 Days Ago
This is a Lexmark rebadge. Check that the toner cartridge contact set is not broken or damaged. =^..^=
13 replies | 569 view(s)
-
3 Days Ago
This is the one I thought of. WSD does not function reliably. Choose a static IP in the driver. =^..^=
6 replies | 585 view(s)
-
3 Days Ago
Those rollers look VERY worn. I'd start there with new rollers. =^..^=
15 replies | 800 view(s)
-
4 Days Ago
OMG. I can see why it's useless. It might work in an isolated situation where a printer is plugged directly to a laptop with a cat5 cable, without...
6 replies | 274 view(s)
-
4 Days Ago
The paper does not look like it is loaded properly. My suggestion is to:
* remove all the paper from tray #2
* perform a U906 partial reset to...
15 replies | 800 view(s)
-
4 Days Ago
Hello Hans.
2000:0006256
You can disregard the part after the colon, that's the copy count.
C2000 is a main motor error (not rotating)....
2 replies | 243 view(s)
-
4 Days Ago
I agree with this one. Konica Minolta CCDs that do very long scan runs are well known for failing on the 654e series, and 808 series. Usually they...
5 replies | 567 view(s)
-
4 Days Ago
Just for us dummies: What is APIPA? =^..^=
6 replies | 274 view(s)
-
5 Days Ago
I happen to agree with your strategy. =^..^=
6 replies | 1163 view(s)
-
5 Days Ago
I've had this before when one of the PCU's waste coil spring had snapped - woth checking if the WTB has recently been changed-check all the PCU's
7 replies | 561 view(s)
-
6 Days Ago
Welcome! =^..^=
4 replies | 235 view(s)
-
6 Days Ago
You are stuck following the process through to it's culmination. Anything else is a forgery. =^..^=
7 replies | 687 view(s)
-
6 Days Ago
Maybe I've got this wrong. Somebody please correct me if I do: WSD only connects with the printers during initialization. If the printer loses...
8 replies | 472 view(s)
-
1 Week Ago
Congratulations on your success!! =^..^=
14 replies | 832 view(s)
-
1 Week Ago
You're in the right place for all of those things. Welcome!! =^..^=
4 replies | 322 view(s)
-
1 Week Ago
If it's drum diameter, there is a chip in the coating of one (or more) of the drums. Take a known good DK-5195, and try it in each location, until...
14 replies | 832 view(s)
-
1 Week Ago
What's the interval of repeating, in millimeters please?
14 replies | 832 view(s)
-
1 Week Ago
The only way this could possibly work is SEF (short edge feed), and with photos, yes you will have separation issues. The smallest acceptable...
1 replies | 203 view(s)
-
1 Week Ago
I found a few whole typewriters on eBay, not too expensive. So far that's the only path forward. =^..^=
3 replies | 1285 view(s)
-
1 Week Ago
I found a few whole typewriters on eBay, not too expensive. So far that's the only path forward. =^..^=
3 replies | 1517 view(s)
-
1 Week Ago
How about you tsb? I have known three female techs in person, and perhaps half dozen more here remotely.
Happy International Women's Day!!
3 replies | 2380 view(s)
-
1 Week Ago
Make sure that your attachments are < 1MB. You may have to change camera settings or crop to get a smaller file size. =^..^=
14 replies | 832 view(s)
-
1 Week Ago
I cleaned the terminals on the back of the Itb assy, then the id sensor
Booted fine, no errors.
3 replies | 434 view(s)
About prntrfxr
- Real Name:
- Lori
- Country:
- United States
- Where are you from (City, State):
- Living in Exile
- Technician Status:
- Experienced Tech (10 yrs+)
- Biography:
- Born in the North, grew up in the south, and like both.
- Interests:
- Part-time artist, part-time guitarist, and part-time video gamer.
- Occupation:
- Head Technician for Laser Printer Parts Company
- What Year Did You Start in this Industry:
- 20+
- Favorite Manufacturer:
- HP
- What was the first machine you worked on:
- Lanier/Toshiba/Ricoh/Savin
- Gender:
- Female
Life should NOT be a journey to the grave with the intention of arriving safely in an attractive and well-preserved body, but rather to skid in sideways - Coke in one hand - chocolate in the other - body thoroughly used up, totally worn out and screaming "WOO-HOO, what a ride!".
Total Posts
- Total Posts
- 1,638
- Posts Per Day
- 0.28
Albums
- Total Albums
- 2
- Total Photos
- 0
Visitor Messages
- Total Messages
- 9
- Most Recent Message
- 06-07-2012
General Information
- Last Activity
- 01-30-2024
- Join Date
- 04-17-2008
- Referrals
- 1
33 Friends
Showing Friends 1 to 10 of 33