-
Older Activity
-
1 Day Ago
This is so smart!
I had one of those horrible moments 16yrs ago. We were moving a CS8030 off of it's busted up pallet. It was me and three other...
9 replies | 591 view(s)
-
1 Day Ago
Welcome! =^..^=
4 replies | 183 view(s)
-
1 Day Ago
Hi, All. Hope everyone is having a decent day. I am looking for the part number of the "booklet tray full" sensors on a SR3220. I located the bracket...
3 replies | 255 view(s)
-
2 Days Ago
I like it. =^..^=
9 replies | 591 view(s)
-
3 Days Ago
There is a tech bulletin on this. 3 steps, 1st reboot device. 2nd is to power it off, after power is off and unplugged push power button again to...
6 replies | 623 view(s)
-
1 Week Ago
I was wondering while I had it apart if I could just get the cleaning assembly if I broke something. Good thing I didn't!
And I suppose I didn't...
4 replies | 292 view(s)
-
1 Week Ago
I can't tell you which models, but once they go into an error code the Settings Menu may become inaccessible. And if you replace the printhead while...
4 replies | 406 view(s)
-
1 Week Ago
Hello all, I've been out of the copier repair business for nearly 10 years at this point and it looks like finding Kyocera firmware is impossible if...
4 replies | 292 view(s)
-
1 Week Ago
Sharp guy here.....
How do I get to lead edge adjust U402 on a printer only model?
TIA
1 replies | 340 view(s)
-
1 Week Ago
There's a third & fourth choice:
3rd: Ends up under the heaviest object in the room, regardless of how far away.
4rth: Is magnetically attracted...
4 replies | 231 view(s)
-
1 Week Ago
Welcome! =^..^=
5 replies | 379 view(s)
-
2 Weeks Ago
Welcome from the other side of the world. =^..^=
4 replies | 201 view(s)
-
2 Weeks Ago
I've never seen the official bulletin, but it's no small task. On later production models they installed a new style front cover with holes to access...
5 replies | 682 view(s)
-
2 Weeks Ago
If I were to guess, I'd guess that the U021 reset cleared the speed upgrade code, so it won't accept that toner, and it will run at 25ppm. I suspect...
14 replies | 1202 view(s)
-
2 Weeks Ago
Thanks Lawrence! That video is a nice demonstration.
26 replies | 3586 view(s)
-
2 Weeks Ago
I like choice #2. Buy the good used replacement. You can part out the old one later on, as needed.
In a very high volume situation it will run...
4 replies | 580 view(s)
-
2 Weeks Ago
So just to clarify: That line is crossfeed? If yes, start with the simplest of solutions: clean every rubber, metal, or plastic roller thoroughly. I...
2 replies | 254 view(s)
-
2 Weeks Ago
Correct. =^..^=
9 replies | 683 view(s)
-
2 Weeks Ago
Those were my conclusions. Once the overtoning starts, replacing the developing unit is the only cure. This is not a machine that you want running...
9 replies | 683 view(s)
-
2 Weeks Ago
Go with the kit. There are detailed instructions in the package. it is important to follow the documentation. If resets are not done before service...
4 replies | 580 view(s)
-
2 Weeks Ago
Kyocera 4501i Dumping Toner
7002i / 8002i development unit problem
Copystar CS3500i
4501i machines overtoning or ghosting alot ???
They all...
9 replies | 683 view(s)
-
3 Weeks Ago
I'm always loathe to disconnect any ribbon cable I don't have to. They damage far too easily. This is my preference too. =^..^=
15 replies | 9195 view(s)
-
3 Weeks Ago
Lol!! The world will always build better idiots.
I remember installing machines in the 1990's. The customer asked us to remove all the function...
15 replies | 1002 view(s)
-
3 Weeks Ago
Lol! At one of the Special Ed buildings we had one of the special ed kids try to remove the screen from a bizhub 951. He was not successful in...
2 replies | 177 view(s)
-
3 Weeks Ago
I agree on this one. We have had a couple cases on high speed Konica Minoltas, in which fanning the paper made all the difference. Between us techs,...
26 replies | 3586 view(s)
-
3 Weeks Ago
That's it......Thank you.
8 replies | 524 view(s)
-
3 Weeks Ago
Is there a way to disable the message that appears on the screen of the copier, that indicates changes have been made via web interface...blah blah...
8 replies | 524 view(s)
-
3 Weeks Ago
Hi, All. Quick question. What is the part number for the transfer belt? I cannot find it in the PC. Do I have to order the whole itb assembly?
4 replies | 450 view(s)
About prntrfxr
- Real Name:
- Lori
- Country:
- United States
- Where are you from (City, State):
- Living in Exile
- Technician Status:
- Experienced Tech (10 yrs+)
- Biography:
- Born in the North, grew up in the south, and like both.
- Interests:
- Part-time artist, part-time guitarist, and part-time video gamer.
- Occupation:
- Head Technician for Laser Printer Parts Company
- What Year Did You Start in this Industry:
- 20+
- Favorite Manufacturer:
- HP
- What was the first machine you worked on:
- Lanier/Toshiba/Ricoh/Savin
- Gender:
- Female
Life should NOT be a journey to the grave with the intention of arriving safely in an attractive and well-preserved body, but rather to skid in sideways - Coke in one hand - chocolate in the other - body thoroughly used up, totally worn out and screaming "WOO-HOO, what a ride!".
Total Posts
- Total Posts
- 1,638
- Posts Per Day
- 0.28
Albums
- Total Albums
- 2
- Total Photos
- 0
Visitor Messages
- Total Messages
- 9
- Most Recent Message
- 06-07-2012
General Information
- Last Activity
- 3 Weeks Ago
- Join Date
- 04-17-2008
- Referrals
- 1
33 Friends
Showing Friends 1 to 10 of 33