Tab Content
  • repn1999's Avatar
    3 Weeks Ago
    repn1999 replied to a thread DADF K1 in Canon
    Sounds to me like something in the doc feeder is knocked out of place causing the machine to think something is in the doc feeder. could be a loose...
    1 replies | 144 view(s)
  • repn1999's Avatar
    3 Weeks Ago
    repn1999 replied to a thread Mx 7090 card reader issues in Sharp
    I would also suggest turning off the turn panel off while in preheat/sleep mode option. I did see this issue on a couple 7040 machines but it ended...
    4 replies | 329 view(s)
  • repn1999's Avatar
    3 Weeks Ago
    I would suggest checking to make sure firmware is up to date. Then check to make sure your density sensor in the transfer unit is clean. I am...
    4 replies | 323 view(s)
  • repn1999's Avatar
    3 Weeks Ago
    repn1999 replied to a thread MX-FN27 in Sharp
    Look at this also
    7 replies | 647 view(s)
  • repn1999's Avatar
    3 Weeks Ago
    no there is not a way to ignore the error and allow the machine to operate. These fans are a known issue on alot of sharp mfps and have been upgraded...
    11 replies | 14335 view(s)
  • repn1999's Avatar
    3 Weeks Ago
    repn1999 replied to a thread MX-4141 E7-11 in Sharp
    run 63-5 shading gamma default for both sides. This will usually fix this issue. Check that firmware is also up to date. You may have to do...
    1 replies | 248 view(s)
  • repn1999's Avatar
    3 Weeks Ago
    I would suggest checking the address to see if it is using the Computer name or IP address. After that I would check to make sure you have a local...
    4 replies | 386 view(s)
  • repn1999's Avatar
    3 Weeks Ago
    PM me
    1 replies | 297 view(s)
  • repn1999's Avatar
    3 Weeks Ago
    Check tray paper type Run sim 50-28 setup adj all select all trays. Check torque limiter Also it is a known issue for paper feed drive units on...
    3 replies | 356 view(s)
  • repn1999's Avatar
    4 Weeks Ago
    repn1999 replied to a thread MX-FN27 in Sharp
    have you ran the machine without the finisher. I agree with the prior post, however an older fuser without the brown pressure roller can cause enough...
    7 replies | 647 view(s)
  • repn1999's Avatar
    4 Weeks Ago
    repn1999 replied to a thread Sharp 2610 curly paper in Sharp
    check your fuser. sharp made a modification in the fuser and changed the pressure roller inside the belt from a orange one to a newer brown one. they...
    15 replies | 926 view(s)
  • repn1999's Avatar
    4 Weeks Ago
    the common causes for this are usually dirty heat belt from client not running heavy color on the right paper/setting worn heat belt paper stuck...
    5 replies | 1209 view(s)
  • repn1999's Avatar
    4 Weeks Ago
    repn1999 replied to a thread [Error Code] H4-02 on MX-3060/MX-6070/MX-5070 in Sharp
    ALSO....do not remove the fuser with the power on. Phoenix machines use a different type of thermistors that can be electrically damaged if...
    15 replies | 2737 view(s)
  • repn1999's Avatar
    4 Weeks Ago
    repn1999 replied to a thread [Error Code] H4-02 on MX-3060/MX-6070/MX-5070 in Sharp
    I would make sure you have a power filter on it and update to latest firmware 7.60. I have also done the dip switch thing and seems to also work but...
    15 replies | 2737 view(s)
  • repn1999's Avatar
    4 Weeks Ago
    repn1999 replied to a thread [Error Code] MX 4141 & F2-65 in Sharp
    There was an firmware update a while back to make the machine less sensitive to toner adding and less prone to present F2 -6X errors. current version...
    5 replies | 415 view(s)
  • repn1999's Avatar
    4 Weeks Ago
    I would check WSD port and maybe turn off SNMP as previously stated. The other thing that has not been said is to check to see if the MFPs are...
    15 replies | 1572 view(s)
No More Results

3 Visitor Messages

  1. I need your help with this, I need the firmware for mx-4111n
    ahmadalqobate76@gmail.com

  2. View Conversation
    I need your help with this, I need the firmware for ARM-355/455. Your help is greatly appreciated.
    Thanks
    silverboss007@gmail.com
  3. View Conversation
    Hi,Can you help me by Providing information regarding copying of Harddisk, I shall be really greatful.Regards. My mail is aosmani@rediffmail.com
Showing Visitor Messages 1 to 3 of 3
About repn1999

Basic Information

Age
38
About repn1999
Real Name:
Wes
Country:
United States
State/County:
us texas
Where are you from (City, State):
Dallas, TX
Occupation:
Senior Image Integration Specialist
What Year Did You Start in this Industry:
2007
Favorite Manufacturer:
Sharp
Most Hated Brand:
KM
What was the first machine you worked on:
SF2040
Last machine you were formally trained on:
MX-6070N
Gender:
Male

Statistics


Total Posts
Total Posts
183
Posts Per Day
0.06
Visitor Messages
Total Messages
3
Most Recent Message
11-26-2017
General Information
Last Activity
3 Weeks Ago
Join Date
05-24-2010
Referrals
0

3 Friends

  1. GREATMAN GREATMAN is offline

    Technician

    GREATMAN
  2. Jas Jas is offline

    Junior Member

    Jas
  3. techmann techmann is offline

    Technician

    techmann
Showing Friends 1 to 3 of 3

10-29-2018


10-22-2018