Tab Content
  • repn1999's Avatar
    2 Days Ago
    First the reason for not using a SSD. There are actually 2. First the controller does not support ncq or ahci modes which a SSD needs for it to...
    8 replies | 247 view(s)
  • repn1999's Avatar
    2 Days Ago
    I can walk you through hard drive replacement. I have all of the required software. Its not really that hard....do not try a ssd. The machine boots...
    8 replies | 247 view(s)
  • repn1999's Avatar
    1 Week Ago
    heres something else that can cause that randomly......transfer belt position clutch on the main drive. there is a mod part for it.
    7 replies | 310 view(s)
  • repn1999's Avatar
    1 Week Ago
    repn1999 replied to a thread MX-N753N Dead Machien in Sharp
    try the mother pwb. The mfp and pcu boards plug into this board...as well as most of the fans switches etc. also try and remove the fuser and power...
    3 replies | 197 view(s)
  • repn1999's Avatar
    1 Week Ago
    repn1999 replied to a thread MX-7040 not allowing color in Sharp
    I have seen this a couple time, and I dont remember the specific setting but its not a board. It's a setting. Does this happen for copy and print or...
    4 replies | 296 view(s)
  • repn1999's Avatar
    1 Week Ago
    repn1999 replied to a thread [Misc] Touch panel on MX-M623n in Sharp
    I have seen this mostly from bad hard drives.....or maybe memory. Also NEVER do a full clone from a different family of machine to another family....
    5 replies | 260 view(s)
  • repn1999's Avatar
    1 Week Ago
    repn1999 replied to a thread Sharp MX-3050N F2-67 code in Sharp
    I have seen the toner suppy tubes broken or missing gears a few times. very odd.
    10 replies | 510 view(s)
  • repn1999's Avatar
    3 Weeks Ago
    repn1999 replied to a thread DIYer looking for help in Sharp
    The gate has been revised. Usually cleaning the shaft and bushings with alcohol fix that. It doesn't have to be perfectly down tight but down enough...
    16 replies | 617 view(s)
  • repn1999's Avatar
    3 Weeks Ago
    repn1999 replied to a thread DIYer looking for help in Sharp
    Your picture is from facing the guide. Look at it looking at the flat bottom side and look to see if the back edge that faces the door when it is...
    16 replies | 617 view(s)
  • repn1999's Avatar
    3 Weeks Ago
    Change the process electrode covers on the rear frame of the machine. There is a mod for this. Also check LSU chutters. Another common issue is the...
    3 replies | 231 view(s)
  • repn1999's Avatar
    4 Weeks Ago
    I have seen this issue and have done the fabric softener sheet thing too. Wanted to point out that there are SEVERAL firmware updates for these, some...
    2 replies | 203 view(s)
  • repn1999's Avatar
    4 Weeks Ago
    repn1999 replied to a thread Sharp MX-3640 in Sharp
    Another common issue is toner dropping onto the laser lens and will cause a void or discolored line in some cases. Its easy to check before changing...
    7 replies | 397 view(s)
  • repn1999's Avatar
    4 Weeks Ago
    repn1999 replied to a thread MX-565n Wrinkling in Sharp
    Do this modification. I know this says for MXM354 and the small machines But the lower cover and mod parts are the same. Idk why Sharp didnt put this...
    11 replies | 557 view(s)
  • repn1999's Avatar
    4 Weeks Ago
    We have tried with AR parts once, and had issues with copy quality. Not immediately but down the road. The machine didnt make half of its cycle and...
    3 replies | 309 view(s)
  • repn1999's Avatar
    4 Weeks Ago
    repn1999 replied to a thread DIYer looking for help in Sharp
    I have added the bulletin showing the issue below. It also lists the new parts needed.
    16 replies | 617 view(s)
  • repn1999's Avatar
    4 Weeks Ago
    repn1999 replied to a thread DIYer looking for help in Sharp
    Hi. I am pretty sure I know your problem. These machines have a really bad know issue with the duplex guide and gate on the upper right door warping....
    16 replies | 617 view(s)
No More Results

2 Visitor Messages

  1. View Conversation
    I need your help with this, I need the firmware for ARM-355/455. Your help is greatly appreciated.
    Thanks
    silverboss007@gmail.com
  2. View Conversation
    Hi,Can you help me by Providing information regarding copying of Harddisk, I shall be really greatful.Regards. My mail is aosmani@rediffmail.com
Showing Visitor Messages 1 to 2 of 2
About repn1999

Basic Information

Age
36
About repn1999
Real Name:
Wes
Country:
United States
State/County:
us texas
Where are you from (City, State):
Dallas, TX
Occupation:
Senior Image Integration Specialist
What Year Did You Start in this Industry:
2007
Favorite Manufacturer:
Sharp
Most Hated Brand:
KM
What was the first machine you worked on:
SF2040
Last machine you were formally trained on:
MX-6070N
Gender:
Male

Statistics


Total Posts
Total Posts
142
Posts Per Day
0.06
Visitor Messages
Total Messages
2
Most Recent Message
05-10-2012
General Information
Last Activity
2 Days Ago
Join Date
05-24-2010
Referrals
0

1 Friend

  1. techmann techmann is offline

    Technician

    techmann
Showing Friends 1 to 1 of 1

03-27-2017


03-23-2017


03-09-2017


02-28-2017