Thanks Thanks:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 12
  1. #1
    Senior Tech 100+ Posts
    Join Date
    May 2013
    Location
    Karachi
    Posts
    131
    Rep Power
    0

    PRO 907 EX error code BR#42

    Dear All,

    I am suddenly having trouble in my pro 907 EX after power up it shows error code BR#48 as i attached image.
    Kindly guide me.
    Thanks in advance.

    Error Code pro 907 EX.jpg


  2. #2
    Technician
    Join Date
    Jul 2008
    Location
    Drummondville, Qc
    Posts
    36
    Rep Power
    20

    Re: PRO 907 EX error code BR#42

    I am getting the same code.

    did tou come up with a solution to BR#48 code?

    please let me know.


  3. #3
    Senior Tech 100+ Posts
    Join Date
    May 2013
    Location
    Karachi
    Posts
    131
    Rep Power
    0

    Re: PRO 907 EX error code BR#42

    Quote Originally Posted by mahou911 View Post
    I am getting the same code.

    did tou come up with a solution to BR#48 code?

    please let me know.
    I resovled this issue by reinstalling the printer controller software.


  4. #4
    Technician
    Join Date
    Jul 2008
    Location
    Drummondville, Qc
    Posts
    36
    Rep Power
    20

    Re: PRO 907 EX error code BR#42

    Do you still have it? Would you be able to provide it?


  5. #5
    Retired 5,000+ Posts slimslob's Avatar
    Join Date
    May 2013
    Location
    Bakersfield, CA
    Posts
    7,059
    Rep Power
    152

    Re: PRO 907 EX error code BR#42

    Quote Originally Posted by mahou911 View Post
    Do you still have it? Would you be able to provide it?
    I am assuming that this has a fiery controller. If you no longer have the instal software that came with the fiery, contact EFI. Electronics for Imaging


  6. #6
    Technician
    Join Date
    Jul 2008
    Location
    Drummondville, Qc
    Posts
    36
    Rep Power
    20

    Re: PRO 907 EX error code BR#42

    Well I don't think there was a Fiery plugged on it. I can acutally change the IP address and Ping the machine, which means there is an interface Inside the machine.


  7. #7
    Retired 5,000+ Posts slimslob's Avatar
    Join Date
    May 2013
    Location
    Bakersfield, CA
    Posts
    7,059
    Rep Power
    152

    Re: PRO 907 EX error code BR#42

    Quote Originally Posted by mahou911 View Post
    Well I don't think there was a Fiery plugged on it. I can acutally change the IP address and Ping the machine, which means there is an interface Inside the machine.
    If there is a fiery, it is mounted under the cover below where the controller is located. I assume that there is a fiery because I don't recognize BR#42 as a main frame or plockmatic service code. Also since mdfurqan2012 said he reinstalled printer controller software, a fiery controller would be the only one that has its own software. GW controller only has firmware and mdfurqan2012 has been around long enough to know the difference.


  8. #8
    Technician
    Join Date
    Jul 2008
    Location
    Drummondville, Qc
    Posts
    36
    Rep Power
    20

    Re: PRO 907 EX error code BR#42

    You must be right then. There is a black wite connectung both the top and bottom at rear side of the machine.

    Would then reinstalling the printer driver work it out. Plus the code is not 42 but 48 as shown on the jpg attached to the first post.


  9. #9
    Technician
    Join Date
    Jul 2008
    Location
    Drummondville, Qc
    Posts
    36
    Rep Power
    20

    Re: PRO 907 EX error code BR#42

    I've tried updating the firmwares and I show no difference still having BR#48 code (BAckup and Restore)

    Any other idea on the problem solution?


  10. #10
    Senior Tech 100+ Posts
    Join Date
    May 2013
    Location
    Karachi
    Posts
    131
    Rep Power
    0

    Re: PRO 907 EX error code BR#42

    Quote Originally Posted by mahou911 View Post
    I've tried updating the firmwares and I show no difference still having BR#48 code (BAckup and Restore)

    Any other idea on the problem solution?
    I reaolved that issue by reinstalling the printer software not by updating machine's.
    Printer software like we install software in fiery controller not firmware.
    So installing printer software by a patch cable directly connect machine with computer. By running an application on computer will install new software in machine and after rebooting machine your issue will resolve.


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here