Results 1 to 9 of 9
  1. #1
    Senior Tech 100+ Posts gkalman2004's Avatar
    Join Date
    Jul 2016
    Location
    cj
    Posts
    151
    Rep Power
    4

    MPC 8002 toner powder everywhere..

    Hi

    I have a "new" MPC8002 Machine with 75k printed pages, i clean the whole machine every 2 month because tonner powder spots etc..
    I know this type have lot of problems but i dont find any idea why the machine loose so much powder in relative short period.
    In the service manual the preventive maintance is around 300 K but i already have the itb full of powder the transfer and also the fusing.
    I don't have problem with the machine except the monthly cleaning, so any idea are welcome if help me to bring a longer time extension...
    Any advice?

    IMAG0677.jpgIMAG0678.jpgIMAG0679.jpgIMAG0680.jpgIMAG0681.jpg


  2. #2
    Field Supervisor 500+ Posts
    Join Date
    Sep 2008
    Location
    Texarkana, TX
    Posts
    545
    Rep Power
    25

    Re: MPC 8002 toner powder everywhere..

    c8002.pdf

    there is a tech bulletin on this


  3. #3
    Senior Tech 100+ Posts gkalman2004's Avatar
    Join Date
    Jul 2016
    Location
    cj
    Posts
    151
    Rep Power
    4

    Re: MPC 8002 toner powder everywhere..

    Quote Originally Posted by LNorris View Post
    c8002.pdf

    there is a tech bulletin on this
    Yes it will help me to make the new settings.
    I already updated all the firmware but the settings matter
    After i search again i find this info also in the cumulated sc file (i missed this one ..thanks for the heads-up)

    Thank you very much

    Last edited by gkalman2004; 02-16-2017 at 07:34 PM.

  4. #4
    Senior Tech 100+ Posts gkalman2004's Avatar
    Join Date
    Jul 2016
    Location
    cj
    Posts
    151
    Rep Power
    4

    Re: MPC 8002 toner powder everywhere..

    Quote Originally Posted by gkalman2004 View Post
    Yes it will help me to make the new settings.
    I already updated all the firmware but the settings matter
    After i search again i find this info also in the cumulated sc file (i missed this one ..thanks for the heads-up)

    Thank you very much

    I checked today the machine but i already have the firmware upgrade and sp SP3301-023 was already set to 0.05 so not helped this tech buletin.
    I have the same situation


  5. #5
    Senior Tech 100+ Posts gkalman2004's Avatar
    Join Date
    Jul 2016
    Location
    cj
    Posts
    151
    Rep Power
    4

    Re: MPC 8002 toner powder everywhere..

    Hi everybody.

    I found my problem source
    I loose toner on the sides of developer unit, it fill the side of the itb with powder and all the machine.

    [Front] p/n: D1363412 (SEAL DEVELOPMENT ROLLER:FRONT UPPER)
    [Rear] p/n: D1363413 (SEAL DEVELOPMENT ROLLER: REAR UPPER)
    I find the rtb with the procedure but only in the pro c5100 model i find it Document ID : RD137146 Troubleshooting Bk toner scattering from the dev unit side seals
    I will do it also for the CYM developer unit the same procedures
    IMAG0714.jpg and the procedure seal.jpg
    I need to do this correction
    seal2.jpg
    Thank's

    Last edited by gkalman2004; 03-12-2017 at 01:32 PM.

  6. #6
    Senior Tech 100+ Posts
    MPC 8002 toner powder everywhere..

    Timmytronic's Avatar
    Join Date
    Oct 2010
    Posts
    201
    Rep Power
    17

    Re: MPC 8002 toner powder everywhere..

    Change the devs. Sounds like they have not been set up properly. I have had this a few times in new machines. Got the Devs and wait 10mims before you initialise. This will make sure you have no static or electric in the Dev that can cause failed set up results and this.

    Hope me that helps.

    Tim.


  7. #7
    Senior Tech 100+ Posts gkalman2004's Avatar
    Join Date
    Jul 2016
    Location
    cj
    Posts
    151
    Rep Power
    4

    Re: MPC 8002 toner powder everywhere..

    Thank you for this delayed answer, i already fixed my machine but...
    Interesting you try to tell me something like every time when i buy a new machine i must change the developer because it is not setup properly??
    Or reading the service manual you can find how to reconfigure the right developer density for the development unit so i just followed the procedure.


  8. #8
    Senior Tech 100+ Posts
    MPC 8002 toner powder everywhere..

    Timmytronic's Avatar
    Join Date
    Oct 2010
    Posts
    201
    Rep Power
    17

    Re: MPC 8002 toner powder everywhere..

    Hiya. I was not saying you had not set it up wrong, I have had new machines but already had been set up from the factory and I don't think they do it to the book.

    What did you do? Was it the devs?

    Tim.


  9. #9
    Senior Tech 100+ Posts gkalman2004's Avatar
    Join Date
    Jul 2016
    Location
    cj
    Posts
    151
    Rep Power
    4

    Re: MPC 8002 toner powder everywhere..

    I read the rtb with the tonner scattering and there was a setting
    i set 3301-023 M/A LowErr:K from 0.10 to 0.05
    the values is ([0.000 to 1.000 / 0.100 /0.001mg/cm2/step]

    first it not fix my problem and is not writen in the rtb ..
    but one step down i find also the 024
    3301-24 M/A LowErr:Col i set also to 0.05
    the values is [0.000 to 1.000 / 0.200 /0.001mg/cm2/step]
    so a little bit bigger but i don't care i set this also to 0.05
    Also i put the new seals with succes on the developer unit
    Until now the machine working well (maybe until the seals come off (i cross my finger))


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here