Multiple Errors

[nysamara]

This is what I have... which one supposed to be the card? I have two Ethernet connections...


File 3-26-17, 12 32 25 PM.jpgFile 3-26-17, 12 32 55 PM.jpgFile 3-26-17, 12 33 11 PM.jpg

[gkalman2004]

This is what I have... which one supposed to be the card? I have two Ethernet connections...


File 3-26-17, 12 32 25 PM.jpgFile 3-26-17, 12 32 55 PM.jpgFile 3-26-17, 12 33 11 PM.jpg

I'm not in front of my machine but i think one is the suplimentary network rj45 with the 2screw also open the sd card cover screw and remove the sd card from slot 1 .

After this check the machine ip from the webinterface i think was the double conection fiery method used with lan cables between the color controler and machine and other lan cable from the machine to lan

Noname.jpgNoname2.jpg

[nysamara]

Is the SD card cover slot 1 located there? in the back of the machine?

[gkalman2004]

Is the SD card cover slot 1 located there? in the back of the machine?

File 3-26-17, 12 32 55 PM.jpg

[nysamara]

I found the card... and removed it... but its a PostScript3 unit Type M2 card

[nysamara]

I removed both... the ethernet card and the SD card

[gkalman2004]

You must find the controler board and remove it
Take a look under the fax board, i don't have any other idea sorry.
Noname3.jpg

[nysamara]

I dont see anything down the fax card... there are only two hard disks and the other pictures are from the other cards...

File 3-26-17, 1 39 29 PM.jpgFile 3-26-17, 1 39 49 PM.jpgFile 3-26-17, 1 40 09 PM.jpgFile 3-26-17, 1 40 25 PM.jpg

[gkalman2004]

Ok i find the documentation change sp5193-001 from 1 to 0 and sp5895-001 from 0 to 1

This is the install part so do it in reverse order

Before you can connect the E-44B to the printer, you must prepare the printer as follows:
• Install the Gigabit Ethernet board in the printer and change the Service Program (SP) mode on the printer.
• Install the “fierydriven®” key top on the printer operation panel.
• Affix the Fiery decal to the printer front cover.
• If needed, disable the GW scanner feature on the printer.
Printer preparation
To prepare the printer for connection
1 Connect the power cord of the printer to a power outlet.
2 Turn ON the printer main power switch.
3 Enter SP mode.
4 Change the setting of SP5193-001 from "0" to "1".
5 Change the setting of SP5895-001 from "0" to "1".
6 Turn OFF the printer main power switch and wait until the main power indicator is off.
7 Remove the slot cover for the Gigabit Ethernet board by removing the two screws shown below.

8 Insert the Gigabit Ethernet board and fasten it with the screws you removed.
Connect the interface cable to the printer’s Gigabit Ethernet board connector.
Note: The interface cable is provided with the E-44B.
10 Connect the other end of the interface cable to the lower RJ-45 connector on the connector panel of the E-44B.
11 Connect the appropriate power cable to the power connector of the E-44B.
12 Attach the Fiery key top decal to the area above the function key to which the Fiery function is assigned.
For information on function key configuration, see the Operating Instructions provided with the printer.

13 Attach the Fiery Decal to the printer front cover.
Read the manual for E44B Attachment 36158
and for E24B ch-c2efi_fsm_final_161216.pdf

And the sp 5193-001 must be 0 but write down what was installed on the machine from the 7 types of controller
[0 to 10 / 0 / 1/step]
0: External Controller is not installed
1: EFI, 2: Ratio, 3: Egret
4: GJ, 5:Creo, 6: QX-100
7: Kurofune
8~10: Reserved

Ps.. put back the sd card (my mistake)

If the fiery was EB34you need to change back these sp's

Do the following to prepare the copier for use with the EB-34:
• Install the Gigabit Ethernet board in the copier.
• Install the Fiery key top on the copier.
• Enter SP mode on the copier and specify the correct SP setting to enable communication between the copier and
the EB-34.
The following SP settings are needed for the EB-34:
• SP5193-001:[1]
• SP5895-001:[1]
• SP5895-002:[0]
• SP5985-001:[1]
• SP4-201-011[1]
• SP4-201-012[1]
• Apply the Fiery decal the copier.

[nysamara]

Wow!!!

Thanks gkalman2004!!!

everything was resolved!! Thanks a lot!!