Likes Likes:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 12
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Nov 2012
    Location
    Gothenburg
    Posts
    74
    Rep Power
    0

    Ricoh mpc 3002 SC 220-01 and now 992

    Got SC 220-01 on this mpc 3002.
    First change polygon-engine and bicu card..
    still 220... then IPU board. still 220.
    Then change compleat LDB (laser unit).
    still 220-01.
    Then I change back to old laser unit.
    At the same time I open right cover and put out the fusing-unit.
    Start up with the cover open.
    Now SC 992 apper insted.
    What ever I do from now I only gor SC 992.
    I can go to sp mode...
    I try uppgrade firmware, but I can only choice firmware, when I press update button the machine just beep... think the 992 is in the backround.

    I have checked the fuse on the PSU.
    My next step is new controllerboard.
    Any one got an idea what to do next?

  2. #2
    Service Manager 1,000+ Posts
    Join Date
    Jun 2012
    Location
    Turnhout
    Posts
    1,662
    Rep Power
    48

    Re: Ricoh mpc 3002 SC 220-01 and now 992

    SC992 An error undetectable by any other SC code occurred
    So, the underneath problem is and stays sc220:

    Laser problem:

    1. Check the connectors.
    2. Replace the laser-synchronizing detector.
    3. Replace the LDB.
    4. Replace the IPU.



  3. #3
    Senior Tech 100+ Posts gkalman2004's Avatar
    Join Date
    Jul 2016
    Location
    cj
    Posts
    157
    Rep Power
    17

    Re: Ricoh mpc 3002 SC 220-01 and now 992

    I fixed last week a 3002 with the same problem error sc220-03, download the point to point schematic and order the harness for the lasser (or check if it is not out or removed the cable from harness)
    i think the part numbers are D0895236 and D1445239 but check yourself
    The cable go from the lasser to the IPU connector CN165 and CN160
    Also check the ground between the machine and right door it is a green one in the back of the machine,
    if the ground cable is cuted you receive also sc 220->240 etc...

  4. #4
    Trusted Tech 50+ Posts
    Join Date
    Nov 2012
    Location
    Gothenburg
    Posts
    74
    Rep Power
    0

    Re: Ricoh mpc 3002 SC 220-01 and now 992

    Quote Originally Posted by gkalman2004 View Post
    I fixed last week a 3002 with the same problem error sc220-03, download the point to point schematic and order the harness for the lasser (or check if it is not out or removed the cable from harness)
    i think the part numbers are D0895236 and D1445239 but check yourself
    The cable go from the lasser to the IPU connector CN165 and CN160
    Also check the ground between the machine and right door it is a green one in the back of the machine,
    if the ground cable is cuted you receive also sc 220->240 etc...
    NICE!!! 220-03 and 220-01 is almost the same just diffrent color on the laser.
    I will oder the cable tomorrow!

  5. #5
    Service Manager 1,000+ Posts
    Join Date
    Jun 2012
    Location
    Turnhout
    Posts
    1,662
    Rep Power
    48

    Re: Ricoh mpc 3002 SC 220-01 and now 992

    a blocked cable is not blocking itself...
    Replacing a cable will be no solution unless you had worked on the laser before the code sc220 came up...
    And that won't be the case, so, think again.

  6. #6
    Senior Tech 100+ Posts gkalman2004's Avatar
    Join Date
    Jul 2016
    Location
    cj
    Posts
    157
    Rep Power
    17

    Re: Ricoh mpc 3002 SC 220-01 and now 992

    Quote Originally Posted by Sweden_GBG View Post
    NICE!!! 220-03 and 220-01 is almost the same just diffrent color on the laser.
    I will oder the cable tomorrow!
    Double check the part numbers on my order one cable the sync was with different harness.

  7. #7
    Senior Tech 100+ Posts gkalman2004's Avatar
    Join Date
    Jul 2016
    Location
    cj
    Posts
    157
    Rep Power
    17

    Re: Ricoh mpc 3002 SC 220-01 and now 992

    Quote Originally Posted by Mark Bbb View Post
    a blocked cable is not blocking itself...
    Replacing a cable will be no solution unless you had worked on the laser before the code sc220 came up...
    And that won't be the case, so, think again.
    I have the same issue almost, i also change the IPU the lasser unit and nothing worked until in my case i changed the harness .
    I can't tell if this will be also in this case but changing the cable with the harness is cheapper than any controller.
    Of course it take some time (my time ~1 hour) you must take out the psu to get out the cable and put the new one from the laser to the IPU

  8. #8
    Trusted Tech 50+ Posts
    Join Date
    Nov 2012
    Location
    Gothenburg
    Posts
    74
    Rep Power
    0

    Re: Ricoh mpc 3002 SC 220-01 and now 992

    Quote Originally Posted by gkalman2004 View Post
    I fixed last week a 3002 with the same problem error sc220-03, download the point to point schematic and order the harness for the lasser (or check if it is not out or removed the cable from harness)
    i think the part numbers are D0895236 and D1445239 but check yourself
    The cable go from the lasser to the IPU connector CN165 and CN160
    Also check the ground between the machine and right door it is a green one in the back of the machine,
    if the ground cable is cuted you receive also sc 220->240 etc...

    gkalman2004 NICE... It was the right nr you got there.. I checked the point to point. Order the cables and report back later =) (there where one more cable, D0295237 that goes to the pologon mirror motor) order this one too...

  9. #9
    Senior Tech 250+ Posts sharpmind's Avatar
    Join Date
    Sep 2009
    Posts
    478
    Rep Power
    34

    Re: Ricoh mpc 3002 SC 220-01 and now 992

    Quote Originally Posted by Sweden_GBG View Post
    gkalman2004 NICE... It was the right nr you got there.. I checked the point to point. Order the cables and report back later =) (there where one more cable, D0295237 that goes to the pologon mirror motor) order this one too...
    From where you get the part number of the connectors. I could not find it in the part manual of the machine MP C3002?

  10. #10
    Field Supervisor 500+ Posts Zaxxon's Avatar
    Join Date
    Jan 2014
    Posts
    607
    Rep Power
    36

    Re: Ricoh mpc 3002 SC 220-01 and now 992

    Quote Originally Posted by sharpmind View Post
    From where you get the part number of the connectors. I could not find it in the part manual of the machine MP C3002?
    Hi

    In the point to point schematic.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here