Likes Likes:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 12
  1. #1
    Senior Tech 250+ Posts
    Join Date
    Jul 2008
    Location
    ashford
    Posts
    337
    Rep Power
    36

    set fuser on MP 5054

    one of my guys has gone to the copier to fit p/r and h/r and thermistor he has fitted all the parts and now the copier says fuser not set .
    he has checked all the wires etc but cant get it to clear any one had this problem.

  2. #2
    Service Manager 10,000+ Posts
    set fuser on MP 5054

    Phil B.'s Avatar
    Join Date
    Jul 2016
    Location
    Raleigh NC
    Posts
    22,659
    Rep Power
    658

    Re: set fuser on MP 5054

    Quote Originally Posted by slot View Post
    one of my guys has gone to the copier to fit p/r and h/r and thermistor he has fitted all the parts and now the copier says fuser not set .
    he has checked all the wires etc but cant get it to clear any one had this problem.
    WHAT WAS THE PROBLEM BEFORE? Was is kicking a fuser error? did he reset the error code?

  3. #3
    Senior Tech 250+ Posts
    Join Date
    Jul 2008
    Location
    ashford
    Posts
    337
    Rep Power
    36

    Re: set fuser on MP 5054

    thanks for the reply the only reason for the roller change was for marks on copies and near life parts no SCs etc.

  4. #4
    Service Manager 10,000+ Posts
    set fuser on MP 5054

    Phil B.'s Avatar
    Join Date
    Jul 2016
    Location
    Raleigh NC
    Posts
    22,659
    Rep Power
    658

    Re: set fuser on MP 5054

    Quote Originally Posted by slot View Post
    thanks for the reply the only reason for the roller change was for marks on copies and near life parts no SCs etc.
    did he reset the parts life?

  5. #5
    Copier Combobulator 500+ Posts
    Join Date
    May 2016
    Posts
    589
    Rep Power
    26

    Re: set fuser on MP 5054

    Quote Originally Posted by slot View Post
    one of my guys has gone to the copier to fit p/r and h/r and thermistor he has fitted all the parts and now the copier says fuser not set .
    he has checked all the wires etc but cant get it to clear any one had this problem.
    I've found it to be very easy to damage the wires in the two small looms you have to connect at the back of the machine. You can be quite easy rip them out of the connector or break them off at the connector.

    They might look ok at a casual glance but be broken.

  6. #6
    Field Supervisor 500+ Posts
    Join Date
    Apr 2010
    Location
    the west
    Posts
    662
    Rep Power
    38

    Re: set fuser on MP 5054

    Quote Originally Posted by sturmtrooper View Post
    I've found it to be very easy to damage the wires in the two small looms you have to connect at the back of the machine. You can be quite easy rip them out of the connector or break them off at the connector.

    They might look ok at a casual glance but be broken.
    I did that on my first time working on a fuser on this model.....

  7. #7
    Senior Tech 250+ Posts
    Join Date
    Jul 2008
    Location
    ashford
    Posts
    337
    Rep Power
    36

    Re: set fuser on MP 5054

    Thanks guys we will re check the connesctors i suspect that is where the problem is

  8. #8
    Field Supervisor 500+ Posts Wild Bill's Avatar
    Join Date
    Jul 2005
    Location
    Fresno, California
    Posts
    774
    Rep Power
    55

    Re: set fuser on MP 5054

    Quote Originally Posted by sturmtrooper View Post
    I've found it to be very easy to damage the wires in the two small looms you have to connect at the back of the machine. You can be quite easy rip them out of the connector or break them off at the connector.

    They might look ok at a casual glance but be broken.
    I agree, also careful and dont break the the rear pressure arm next to it...: (
    Izzy

  9. #9
    Copier Combobulator 500+ Posts
    Join Date
    May 2016
    Posts
    589
    Rep Power
    26

    Re: set fuser on MP 5054

    Quote Originally Posted by jonhiker View Post
    I did that on my first time working on a fuser on this model.....

    It wasn't my first time working on the model, but the first time I went to take the fuser out of a relatively new machine the connectors were in so tight I damaged them. Had to strip the wire back and re-do the connector was not fun. The second time was on an older machine.

    At this point I just use my pliers to grab at an empty wire socket in the connector and work it loose if it doesn't come out easily. When I put it back in I don't shove them in hard like I would most harnesses.

    Luckily it's not often the fusers have to be worked with on these models. I miss the ones where the connector was built into the frame though.

  10. #10
    Senior Tech 250+ Posts DRichard's Avatar
    Join Date
    May 2008
    Location
    Knoxville, TN
    Posts
    482
    Rep Power
    43

    Re: set fuser on MP 5054

    Quote Originally Posted by sturmtrooper View Post

    Luckily it's not often the fusers have to be worked with on these models. I miss the ones where the connector was built into the frame though.
    I agree. It was stupid to replace the "slide in" connection with the riskier/fragile wiring harness.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here