Page 1 of 2 12 LastLast
Results 1 to 10 of 20
  1. #1
    Senior Tech 250+ Posts
    Join Date
    May 2012
    Posts
    295
    Rep Power
    27

    MP 2852 fuser rebuild

    I will be ordering a fuser fuser rebuid kit from Precision Roller. Do I need anything else? I see the manual calls for a grease that should be applied to the UFR. Will any white lithium grease work or do I need a high temp grease? I have the HP grease.




    Savin MP 2852 Fuser Rebuild Maintenance Kit - 120K, Genuine (M4285)

  2. #2
    Trusted Tech 50+ Posts
    MP 2852 fuser rebuild

    TayTayTheTechnician's Avatar
    Join Date
    May 2016
    Location
    Sacramento, CA
    Posts
    51
    Rep Power
    17

    Re: MP 2852 fuser rebuild

    Quote Originally Posted by campy View Post
    I will be ordering a fuser fuser rebuid kit from Precision Roller. Do I need anything else? I see the manual calls for a grease that should be applied to the UFR. Will any white lithium grease work or do I need a high temp grease? I have the HP grease.




    Savin MP 2852 Fuser Rebuild Maintenance Kit - 120K, Genuine (M4285)
    You are better off with high temp grease, but regular white grease will do the trick. Keep an eye out for the plates that the lamp screws into as the might fall out one the lamp is out. It's pretty easy

  3. #3
    It's not easy being green 1,000+ Posts Cipher's Avatar
    Join Date
    May 2006
    Posts
    1,309
    Rep Power
    57

    Re: MP 2852 fuser rebuild

    I normally carry hot roller bearings as well (just in case).
    They do wear / dry out which can cause a clicking / creaking noise.

    Results for G052 4618
    • Knowledge not shared, is eventually knowledge that becomes lost... like tears in the rain.

    Fully qualified technician for Ricoh - Canon - Sharp - HP - Brother

  4. #4
    Service Manager 1,000+ Posts fshead's Avatar
    Join Date
    Jan 2009
    Location
    nyc
    Posts
    2,339
    Rep Power
    80

    Re: MP 2852 fuser rebuild

    you can buy the teflon grease and if bearings are tight some triflow will loosen up
    any gunk and free them..........i would suggest you pay attemtion where the upper fusing bearing sits on the frame as it is easy to put it in a bit off..at least as i remember mp 2027...you dont want the fuser gear hitting the frame,,,,,,,,,,,clean all thermisters if not changing them........clean metal cleaning roller

  5. #5
    SanDiegoCopierRepair.com 1,000+ Posts
    MP 2852 fuser rebuild

    blazebusiness's Avatar
    Join Date
    Apr 2010
    Location
    From NY--- live in San Diego , Ca.
    Posts
    1,248
    Rep Power
    51

    Re: MP 2852 fuser rebuild

    Quote Originally Posted by campy View Post
    I will be ordering a fuser fuser rebuid kit from Precision Roller. Do I need anything else? I see the manual calls for a grease that should be applied to the UFR. Will any white lithium grease work or do I need a high temp grease? I have the HP grease.




    Savin MP 2852 Fuser Rebuild Maintenance Kit - 120K, Genuine (M4285)

    That fuser heats up to around 190F degrees so use a high temp grease or at least verify that the regular grease you are using can handle those temps. Not sure what you mean by HP grease (Hewlett Packard?) If the HP grease you mentioned is the one they use for lubricating the inside of HP fuser sleeves----that should be fine.
    Anything can be made to work if you fiddle with it long enough- San Diego Copier Repair.com

  6. #6
    Senior Tech 250+ Posts
    Join Date
    May 2012
    Posts
    295
    Rep Power
    27

    Re: MP 2852 fuser rebuild

    Quote Originally Posted by blazebusiness View Post
    That fuser heats up to around 190F degrees so use a high temp grease or at least verify that the regular grease you are using can handle those temps. Not sure what you mean by HP grease (Hewlett Packard?) If the HP grease you mentioned is the one they use for lubricating the inside of HP fuser sleeves----that should be fine.
    It is.

  7. #7
    Retired 10,000+ Posts
    MP 2852 fuser rebuild

    slimslob's Avatar
    Join Date
    May 2013
    Location
    Bakersfield, CA
    Posts
    34,128
    Rep Power
    989

    Re: MP 2852 fuser rebuild

    I use Super Lube. Yu can order it online or check with you nearest Harbor Freight. I also pack the bearings with either super lube or silicon heat sink compound.
    https://www.harborfreight.com/catalo...f&q=Super+Lube

  8. #8
    Senior Tech 250+ Posts tufbnme's Avatar
    Join Date
    Feb 2008
    Location
    BUILD THE WALL! State
    Posts
    489
    Rep Power
    38

    Re: MP 2852 fuser rebuild

    I also include the UFR bearings when rebuilding these fusers.

  9. #9
    Senior Tech 250+ Posts tufbnme's Avatar
    Join Date
    Feb 2008
    Location
    BUILD THE WALL! State
    Posts
    489
    Rep Power
    38

    Re: MP 2852 fuser rebuild

    Quote Originally Posted by slimslob View Post
    I use Super Lube. Yu can order it online or check with you nearest Harbor Freight. I also pack the bearings with either super lube or silicon heat sink compound.
    https://www.harborfreight.com/catalo...f&q=Super+Lube
    I have used that stuff and it smells pretty bad when burning off, lost a customer because of it.

  10. #10
    Senior Tech 250+ Posts tufbnme's Avatar
    Join Date
    Feb 2008
    Location
    BUILD THE WALL! State
    Posts
    489
    Rep Power
    38

    Re: MP 2852 fuser rebuild

    Quote Originally Posted by Cipher View Post
    I normally carry hot roller bearings as well (just in case).
    They do wear / dry out which can cause a clicking / creaking noise.

    Results for G052 4618
    I use the AE030047 just remove the collar or keep it on if the frame is broken.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here