Results 1 to 10 of 10
  1. #1
    Senior Tech 250+ Posts
    Join Date
    Jul 2008
    Location
    ashford
    Posts
    337
    Rep Power
    36

    Mpc2003 jamming at exit

    Im looing for some advice here as we have a very low volume MPc2003 that has for the last few weeks been jamming with code 20 and 24.
    The paper is just coming out of the fuser it will only once in a blue moon do this so the engineer has only seen it once.
    We have changed the complete fuser and all the fuser exit senor and the inverter senor and the sensor on the transfer unit we have also tried a new transfer belt unit
    We can seem to get on top of this we have also change the inverter gate and solenoid and of course upgraded the firmware.
    All of this and we still have a problem can anyone shine any light on this problem thanks.

  2. #2
    Service Manager 1,000+ Posts
    Join Date
    Jun 2012
    Location
    Turnhout
    Posts
    1,662
    Rep Power
    48

    Re: Mpc2003 jamming at exit

    is machine standing in a normal environement?
    Does the paper stay for a long period in the paper tray?
    Is the problem the same with a new paper out of the box?
    Is it solved with a tray heater?
    Are the paper guides in the paper tray at a position they should be?
    ...

  3. #3
    Senior Tech 250+ Posts
    Join Date
    Jul 2008
    Location
    ashford
    Posts
    337
    Rep Power
    36

    Re: Mpc2003 jamming at exit

    Thanks for your reply we have given them fresh paper to try after it jams which didnt improve it and all the guides are in the correct positions and we have changed the feed in one tray its very odd.

  4. #4
    Service Manager 1,000+ Posts
    Join Date
    Jun 2012
    Location
    Turnhout
    Posts
    1,662
    Rep Power
    48

    Re: Mpc2003 jamming at exit

    paper isn't wrapped, so it is a matter of electronic failure.
    Put the paper size in all trays to a fixed one, solved?
    Moisture can build up at sensors, fan broke (but then a code would come up)?
    ???

  5. #5
    Senior Tech 250+ Posts sharpmind's Avatar
    Join Date
    Sep 2009
    Posts
    478
    Rep Power
    34

    Re: Mpc2003 jamming at exit

    Quote Originally Posted by slot View Post
    Im looing for some advice here as we have a very low volume MPc2003 that has for the last few weeks been jamming with code 20 and 24.
    The paper is just coming out of the fuser it will only once in a blue moon do this so the engineer has only seen it once.
    We have changed the complete fuser and all the fuser exit senor and the inverter senor and the sensor on the transfer unit we have also tried a new transfer belt unit
    We can seem to get on top of this we have also change the inverter gate and solenoid and of course upgraded the firmware.
    All of this and we still have a problem can anyone shine any light on this problem thanks.
    I have encountered that problem. See if the duplex unit is broken or not. Make sure that part is aligned properly otherwise paper will jam.Capture.JPG

  6. #6
    Senior Tech 250+ Posts
    Join Date
    Jul 2008
    Location
    ashford
    Posts
    337
    Rep Power
    36

    Re: Mpc2003 jamming at exit

    thanks for all you help we will try the dplex unit

  7. #7
    Junior Member
    Join Date
    Mar 2011
    Posts
    9
    Rep Power
    0

    Re: Mpc2003 jamming at exit

    Does the machine have a one bin tray and have you installed the gear that comes with the one bin tray unit ?

  8. #8
    Senior Tech 100+ Posts
    Join Date
    Mar 2009
    Location
    Marianna, FL
    Posts
    158
    Rep Power
    32

    Re: Mpc2003 jamming at exit

    look at he jam codes and see if you have a lot of power on jams. J001. if you do replace the right side door.

  9. #9
    Service Manager 1,000+ Posts
    Join Date
    Jun 2012
    Location
    Turnhout
    Posts
    1,662
    Rep Power
    48

    Re: Mpc2003 jamming at exit

    Solved?

  10. #10
    Junior Member
    Join Date
    Apr 2010
    Location
    Kelowna
    Posts
    8
    Rep Power
    0

    Re: Mpc2003 jamming at exit

    I had exact same issue yesterday & fixed it today. As Sharpmind said, the broken Duplex entrance guide was the cause. the M/C started working as soon as the guide was replaced. the catch on the rear side of the assembly was broken & the entire assembly was out of home position.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here