Question regarding 2-3 hole punch unit on a sr3110 booklet finisher

[fshead]

greetings
I am running a spc830dn that i connected to a sr3110 booklet finisher that has the 2-3 hole punch unit.
When i go to accessories i see i can hit 2-3hole punch,2and4 holes EU and 4 hole type NE.
Can these be configured to any of the 3?
I do see more that 3 hole cutters on the unit
thanks

[slimslob]

You probably see 5 individual cutters. 2 are for 2-hole punching and the other 3 are for 3-hole. The 2-4 hole punch is only available in EU, Europe. It is a physically different punch head. You might be able to select it but will only get 2 and 3 hole punching.

[fshead]

You probably see 5 individual cutters. 2 are for 2-hole punching and the other 3 are for 3-hole. The 2-4 hole punch is only available in EU, Europe. It is a physically different punch head. You might be able to select it but will only get 2 and 3 hole punching.

thanks
i saw the 5 cutters.
I am having issues trying to figure out how to configure printing using the booklet fold option.
I have seen it on mpc3003/mpc4503 and the option shows up on the screen when using copy mode but I cant
figure how to do it in pcl6 nor ps3 drivers installed.
It shows the right model sr3110 on the screen and when i check accessories...

[slimslob]

thanks
i saw the 5 cutters.
I am having issues trying to figure out how to configure printing using the booklet fold option.
I have seen it on mpc3003/mpc4503 and the option shows up on the screen when using copy mode but I cant
figure how to do it in pcl6 nor ps3 drivers installed.
It shows the right model sr3110 on the screen and when i check accessories...

On the accessories make sure the SR3110 finisher is checked and applied.
On the print Properties go to the Detailed Setting tab select finishing, staple: 2 at center.

[fshead]

On the accessories make sure the SR3110 finisher is checked and applied.
On the print Properties go to the Detailed Setting tab select finishing, staple: 2 at center.

thanks
all is on but what i dont see is the fold option that i see when i look at a mpc3003 that has a booklet finisher option..
does the sr3110 Not allow the fold option that sits below the staple and punch in finishing detailed settings?

[fshead]

I installed both spc831dn and mpc4502 on my PC and added the sr3110 and it looks like you can not ask prints to just fold like
you can on the mpc3503 and mpc4503 sorters.
I dont install many sorters on color units i sell.
Another lesson learned

[slimslob]

thanks
all is on but what i dont see is the fold option that i see when i look at a mpc3003 that has a booklet finisher option..
does the sr3110 Not allow the fold option that sits below the staple and punch in finishing detailed settings?

If you send a single sheet job to a booklet finisher and select staple 2 center, it will just fold.

[fshead]

If you send a single sheet job to a booklet finisher and select staple 2 center, it will just fold.

Thanks.
At first i thought maybe it was not in the design.
I will run it tommrw

[fshead]

If you send a single sheet job to a booklet finisher and select staple 2 center, it will just fold.

you were dead on.
it folds on single copy staple 2 center.
I guess multiple sets are not an option.
that sorter weighs a ton,i thought i could just lift it into my van by hand.

[slimslob]

you were dead on.
it folds on single copy staple 2 center.
I guess multiple sets are not an option.
that sorter weighs a ton,i thought i could just lift it into my van by hand.

If there are 2 or more sheets, it assumes that you want them stapled.

You can lay it on the back side and slide it in using a sheet of card board. Stand it up and tie it in to transport.