Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 10 of 10
  1. #1
    Trusted Tech 50+ Posts angelntx's Avatar
    Join Date
    Aug 2009
    Location
    San Antonio, Texas
    Posts
    62
    Rep Power
    30

    Ricoh MP906-Constant empty waste toner container message.

    Ok here is what's going on. We have 2 Ricoh 906s with the same issue. Empty waste toner message. We've called Ricoh tech support and replaced what they had suggested: the bottle, sensors, wire harness and motor. No luck the machine will run about 600 copies then shows the message to empty it. If you wiggle the bottle the message goes way but then comes right back. We looked for a counter or timer setting-nothing. Any tech pubs or ideas would be appreciated.

    angel

  2. #2
    Senior Tech 250+ Posts
    Join Date
    Jul 2008
    Location
    ashford
    Posts
    337
    Rep Power
    36
    Go round the back of the copier and give the rear of the toner supply unit a good vac uout there is a sensor at the back that gets toner on it and on the mp9000 can play up

  3. #3
    Service Manager 250+ Posts zyqwiz's Avatar
    Join Date
    Jun 2009
    Location
    Watford
    Posts
    334
    Rep Power
    33
    Seeing as you are calling a Pro 906ex an MP906, you are aware that there are 2 waste boxes?

  4. #4
    Vacuum Cleaning Expert 1,000+ Posts iMind's Avatar
    Join Date
    Mar 2008
    Location
    File not found
    Posts
    1,116
    Rep Power
    45
    Quote Originally Posted by angelntx View Post
    Ok here is what's going on. We have 2 Ricoh 906s with the same issue. Empty waste toner message. We've called Ricoh tech support and replaced what they had suggested: the bottle, sensors, wire harness and motor. No luck the machine will run about 600 copies then shows the message to empty it. If you wiggle the bottle the message goes way but then comes right back. We looked for a counter or timer setting-nothing. Any tech pubs or ideas would be appreciated.

    angel
    Enter SP2-950-001 ”Page Allowed After Toner Collection Unit Lock”. set to 0 that it.
    We can all Win, but at the end we all loose. Save the greyhound

  5. #5
    Ricoh tech 100+ Posts
    Ricoh MP906-Constant empty waste toner container message.

    collme's Avatar
    Join Date
    Apr 2010
    Location
    huddersfield
    Posts
    221
    Rep Power
    34
    generally it is the waste bottle located near the 2 toner bottles that is forgotton about and causes constant messages. this has sensor in rear of machine that can get very dirty and throw up phantom messages

  6. #6
    Trusted Tech 50+ Posts angelntx's Avatar
    Join Date
    Aug 2009
    Location
    San Antonio, Texas
    Posts
    62
    Rep Power
    30
    Update: Zyqwiz- yes I am aware that there are 2 waste bottles. I was referring to the one that's under the 2 toner bottles not the recycle waste bottle on the paper feed side...that one does have a timer that needs to be reset to zero after 557 hours to 600 hours of use when it requires replacement.
    iMind-Thank you for the suggestions. I'll have the tech check it out on monday
    collme and slot-Thank you also for the suggestion. The BIG boss got a hold of him and had him clean out the back. Apparently he hadn't.

  7. #7
    Service Manager 250+ Posts zyqwiz's Avatar
    Join Date
    Jun 2009
    Location
    Watford
    Posts
    334
    Rep Power
    33
    The waste toner path to the small bottle can get all bunged up and need stripping right down

  8. #8
    Trusted Tech 50+ Posts angelntx's Avatar
    Join Date
    Aug 2009
    Location
    San Antonio, Texas
    Posts
    62
    Rep Power
    30
    Update: Found that the clutch that helps send the toner back up the auger to the toner bank was not working correctly. We performed a toner bank setup and saw the auger turn but during normal copying it would turn on at strange intervals. We were running 1000 copies and it didn't turn until after 246 copies then again after another 187 copies. By the time it went another 150 copies it turned but we saw one of the gears hesitate the the waste toner full message appeared. After replacing the clutch it started to feed the toner to the toner bank at 88 copies then again at 72, 78, 64,71 and so on. We completed the 1000 copy test and the message didn't reappear. Hope that this helps anyone else with this problem.
    thank you all for the assistance.

  9. #9
    Junior Member
    Join Date
    Jul 2010
    Location
    Sydney
    Posts
    8
    Rep Power
    0
    Which clutch is that?

  10. #10
    Vacuum Cleaning Expert 1,000+ Posts iMind's Avatar
    Join Date
    Mar 2008
    Location
    File not found
    Posts
    1,116
    Rep Power
    45
    Behind the fly wheel.
    We can all Win, but at the end we all loose. Save the greyhound

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here