Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 7 of 7
  1. #1
    Senior Tech 250+ Posts
    Join Date
    Sep 2010
    Location
    mashad
    Posts
    261
    Rep Power
    0

    aften a5 and sometimes a4 jamming under registration roller(2035)

    yesterday i copied 500 pages continuously and after that jamming occurred periodically more with a5
    when this jamming occurred i clean the registration roller with cotton and alcohol and for a while jamming eliminated but after few copying , reappeared again.
    the shape of jamming paper is folding in the bottom of paper
    please guide me about troubleshooting this trouble
    thanks a lot
    Color printing with lowest cost per page is my love.

  2. #2
    Senior Tech 250+ Posts
    Join Date
    Sep 2010
    Location
    mashad
    Posts
    261
    Rep Power
    0

    Re: aften a5 and sometimes a4 jamming under registration roller(2035)

    i removed transfer unit and try rotating manually the gear of transfer belt but unlike previous belf not rotated(only the shaft rotated)
    do you think that jamming of paper because of this not rotating belt?
    please guide me about troubleshooting not rotating belt
    thanks a lot
    Color printing with lowest cost per page is my love.

  3. #3
    Service Manager 1,000+ Posts
    aften a5 and sometimes a4 jamming under registration roller(2035)

    teebee1234's Avatar
    Join Date
    Jul 2008
    Location
    Atlanta, GA
    Posts
    1,671
    Rep Power
    58

    Re: aften a5 and sometimes a4 jamming under registration roller(2035)

    If the jam occurs at/before the registration roller, then the transfer unit shouldn't have any effect since it is located above the registration roller (but you still need to correct the problem with the transfer unit). It's common for the registration clutch to fail at some point on these models. so I would replace that first (may want to do the feed clutches too if you have them).

  4. #4
    Senior Tech 250+ Posts vargue's Avatar
    Join Date
    Oct 2011
    Location
    alexandria
    Posts
    405
    Rep Power
    30

    Re: aften a5 and sometimes a4 jamming under registration roller(2035)

    this problem happens to me first show that first switch in controller board is left or up and last switch up also then detect that ther is two spring in copier body and touch with solid piece in transfer body also this problem conclusion to fuser unit can't acquire amount of volt that can be work correctly check that fuser unit moves smoothly good luck

  5. #5
    Toner Monkey 250+ Posts
    Join Date
    Mar 2008
    Posts
    418
    Rep Power
    38

    Re: aften a5 and sometimes a4 jamming under registration roller(2035)

    First place I'd be looking is the registration clutch. If memory serves (though it might be my memories of the earlier 1035 and/or the 350 which are very similar) you can actually strip the clutches down on this model by prying off the brass retaining ring. Strip it down and clean all of the internals with IPA alcohol, alternatively if the clutch doesn't come apart, soak it in IPA for a good hour (do any other servicing work whilst you wait) dry it out thoroughly with air duster and put it back in and give it another try.

    If worst comes to the worst, replace the clutch.

  6. #6
    Senior Tech 250+ Posts
    Join Date
    Sep 2010
    Location
    mashad
    Posts
    261
    Rep Power
    0

    Re: aften a5 and sometimes a4 jamming under registration roller(2035)

    i solved the problem as remove transfer unit and transfer belt but this time the only a5 jamming in fuser and a4 not jamming in fuser
    please guide me troubleshooting this problem
    Color printing with lowest cost per page is my love.

  7. #7
    Service Manager 1,000+ Posts
    aften a5 and sometimes a4 jamming under registration roller(2035)

    teebee1234's Avatar
    Join Date
    Jul 2008
    Location
    Atlanta, GA
    Posts
    1,671
    Rep Power
    58

    Re: aften a5 and sometimes a4 jamming under registration roller(2035)

    Originally you stated that it was jamming under the registration roller, which I understood to mean between the paper feed and registration roller. If you are now saying that you get jams at the fuser entrance on certain sizes, the first thing to do is remove the fuser and inspect it. You may have toner buildup on the entrance guide that is catching the lead edge of the paper or the pressure roller is too soft or the strippers are catching. You need to provide more details on what exactly is happening (also, what is the jam code). If possible, post a picture of the jam as it is in the machine.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here