Results 1 to 10 of 10
  1. #1
    Senior Tech 100+ Posts
    Join Date
    Feb 2008
    Location
    KK
    Posts
    155
    Post Thanks / Like
    Rep Power
    15

    Question Aficio 700 sc441 come out

    What the probebly problem if the A700 appear SC441.I ve notice the toner harden at lower mag roller,but why.
    if A650 the clearence between the DV tank and Drum Can be adjusted but this model are fix.so what should I do?


  2. #2
    Old Retired IKON Drudge
    Join Date
    Apr 2008
    Location
    Reidsville, North Carolina
    Posts
    41
    Post Thanks / Like
    Rep Power
    13
    The mechanical components of this print engine are based on the ancient analog FT5590 family. These machines would go into development motor lock when the development units were badly worn and/or the drive gears were badly worn. These machines also will lock up if one is using non-Ricoh developer and/or toner as they will overfill the unit. First thing I would do is clean out the unit. Vacuum out all the old developer you can; this will take much time as it is necessary to get out all you possibly can. Clean the magnetic rollers with Scotchbrite or similar non-metallic abrasive pad. With the unit empty, check it for binds. If it does not turn freely, I would suggest replacing the unit. You can get bearings and seals, but we never found it cost effective to rebuild as the units are jig assembled at the factory and one cannot get them perfect in the field. If the unit if free, install new Ricoh developer, going through all the steps in the manual. If the SC441 still occurs, it is time to replace the drive train to the development section. Not a fun prospect.

    Doc


  3. #3
    Service Manager 100+ Posts Polo-022's Avatar
    Join Date
    Sep 2007
    Posts
    233
    Post Thanks / Like
    Rep Power
    0

    Smile

    I think you have to check magn. roller o-ring bearings,then the idler gear between mag. and paddle roller. They use to stuck.
    Otherwise fit a new bearing on developer drive motor assy.
    Magnetic roll bearings can cause that feeling of hardened developer. Take a look!!


  4. #4
    unTrusted Tech 100+ Posts imaginemoko's Avatar
    Join Date
    Jan 2008
    Location
    Saudi
    Posts
    198
    Post Thanks / Like
    Rep Power
    15
    verify the toner and developer if its genuine ricoh... then clean the dev unit, check the bearings lubricate it... if faulty.... then replace.......


  5. #5
    Senior Tech 100+ Posts
    Join Date
    Apr 2008
    Location
    Green Bay, WI
    Posts
    116
    Post Thanks / Like
    Rep Power
    14
    Check your Developer drive motor , that is the most common thing to cause that code , there is a bushing in it that wears out.


  6. #6
    Senior Tech 100+ Posts
    Join Date
    Feb 2008
    Location
    KK
    Posts
    155
    Post Thanks / Like
    Rep Power
    15
    Thank you all 4 ure reply.

    One more my question in my head......... is it because of the dv roller not turning cause the toner hardened in between the mag roller and the casing or the friction of toner becouse of the gap from roller to the drum.

    Just for our point to think.................

    in fact the toner will melt when there are heat build-up.
    what I ve found is the toner melt and become like a raisin.

    And if I change all thous parts and using a ginuene parts on dv ,toner.
    then the problem doesn't exsist?




    Become a technician is not a bad job I think


  7. #7
    Field Supervisor 500+ Posts Fearless V K's Avatar
    Join Date
    May 2007
    Location
    Redding, California
    Posts
    621
    Post Thanks / Like
    Rep Power
    21
    If the machine is building up excessive amounts of heat (enough to melt toner on the dv roller, make sure your exhaust fan filters are not clogged up.


  8. #8
    Senior Tech 100+ Posts
    Join Date
    Feb 2008
    Location
    KK
    Posts
    155
    Post Thanks / Like
    Rep Power
    15

    Talking

    If I print just in 150 cps after warm up then the sc441 appear.its not a long time to build a heat around the drum.
    I mean after I have service and clean up the tank and drum.an on the machine.Runs in 150 copies.

    May be an alien there.ha ha ha ......................


  9. #9
    Technician
    Join Date
    Apr 2008
    Posts
    28
    Post Thanks / Like
    Rep Power
    0
    clean the devolper & drum motor


  10. #10
    Senior Tech 100+ Posts
    Join Date
    Feb 2008
    Location
    KK
    Posts
    155
    Post Thanks / Like
    Rep Power
    15
    thanks for your reply.actually the situation is this.
    the toner harden at dv unit on mg roller.the motor nothing wrong.
    I wonder why the toner become hardened there?
    how ever Ive change the dv tank unit and its ok now





    there are many possibality in this world its not wrong if we give any suggestion to the comunity

    thanks man


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here