Aficio MP161 -Print /scan Ricoh, Savin, Gestetner  |
3 Weeks Ago
|
#1 (permalink)
| | Trusted Tech 50+ Posts
Join Date: Feb 2009 Location: Toronto
Posts: 54
Rep Power: 2  | Aficio MP161 -Print /scan I have posted before with questions about this machine and the printing/scanning SD card(s). I have resolved most of my problems with some helpful suggestions from here; however, I have a new issue that's giving me grief.
Originally, I acquired an MP161 that was supposed to have the Print /scan installed, but the card had been removed. I held on to the machine in the hopes that i could obtain a card
I've since acquired another machine that does have the Print/ scan card installed and works perfectly, so I decided to swap it into the other machine and check the functionality.
I was able to make it print, but I can't access the WIM to set the network settings for "scan to folder", etc. I get a "404 NOT FOUND" error.
I was able to set a scan destination via the control panel; however, this is a very tedious process.
I updated ALL firmware, did a complete memory clear (SP5-801), checked all the network settings I could find in SP mode, and checked that "Web" is enabled in "telnet". Nothing seems to get me past the error, there also doesn't appear to be any bulletins on TSC Ricoh about this issue.
I guess my question is, would this have anything to do with the SD card? In other words, does the card pair itself to the machine when it is initially installed, and therefore a "fresh" card may resolve my problem? or is there another solution I may be missing?
I found out the the Print/scan cards aren't too expensive from Ricoh, but I'd like to know if acquiring one is going to solve my problem first
Thanks guys! | | | |
| |
3 Weeks Ago
|
#2 (permalink)
| | Vacuum Cleaning Expert 500+ Posts
Join Date: Mar 2008 Location: File not found
Posts: 827
Rep Power: 12  | Do you mean 5.828.09 is enabled (1) web operation | | |
__________________________ We can all Win, but at the end we all loose. Save the greyhound |
| |
3 Weeks Ago
|
#3 (permalink)
| | Trusted Tech 50+ Posts
Join Date: Feb 2009 Location: Toronto
Posts: 54
Rep Power: 2  | | Quote: | | | Originally Posted by iMind | | | | | | Do you mean 5.828.09 is enabled (1) web operation | | | | | Yes, that's correct | | | |
| |
3 Weeks Ago
|
#4 (permalink)
| | Vacuum Cleaning Expert 500+ Posts
Join Date: Mar 2008 Location: File not found
Posts: 827
Rep Power: 12  | there are two boards B880-5171 GDI Nob
B880-5172 GDI basic
GW board on the spf is B284-5150 so there are three boards the last one is a SPF so that one my be out of question.
found this on the net:
"With GDI or GW controller model. For USA/Europe basic model. Version. Program No. Effective Date .... B8665171E or later PCB:KC3-S:GDI-NOB:ASS'Y ..." | | |
__________________________ We can all Win, but at the end we all loose. Save the greyhound |
| |
3 Weeks Ago
|
#5 (permalink)
| | Senior Tech 100+ Posts
Join Date: Jun 2009 Location: Watford
Posts: 157
Rep Power: 0  | | Quote: | | | | | | | | | Originally, I acquired an MP161 that was supposed to have the Print /scan installed, but the card had been removed. | | | | | No it hadn't - the MP161 does not have print/scan and cannot be upgraded. You have to get a MP161spf for proper print/scan. | | | |
| |
3 Weeks Ago
|
#6 (permalink)
| | Technician
Join Date: Oct 2009 Location: Kyiv
Posts: 13
Rep Power: 1  | | Quote: | | | | | | | | | I have posted before with questions about this machine and the printing/scanning SD card(s). I have resolved most of my problems with some helpful suggestions from here; however, I have a new issue that's giving me grief.
Originally, I acquired an MP161 that was supposed to have the Print /scan installed, but the card had been removed. I held on to the machine in the hopes that i could obtain a card
I've since acquired another machine that does have the Print/ scan card installed and works perfectly, so I decided to swap it into the other machine and check the functionality.
I was able to make it print, but I can't access the WIM to set the network settings for "scan to folder", etc. I get a "404 NOT FOUND" error.
I was able to set a scan destination via the control panel; however, this is a very tedious process.
I updated ALL firmware, did a complete memory clear (SP5-801), checked all the network settings I could find in SP mode, and checked that "Web" is enabled in "telnet". Nothing seems to get me past the error, there also doesn't appear to be any bulletins on TSC Ricoh about this issue.
I guess my question is, would this have anything to do with the SD card? In other words, does the card pair itself to the machine when it is initially installed, and therefore a "fresh" card may resolve my problem? or is there another solution I may be missing?
I found out the the Print/scan cards aren't too expensive from Ricoh, but I'd like to know if acquiring one is going to solve my problem first
Thanks guys! | | | | | As alternative you can use SmartDeviceMonitor for Admin.
1. Maybe SSL activated on MFP? In this case use httpS://<ip address>
2. Maybe somebody chanched the access control range? In this case you can access on MFP by telnet by command "access"
You must print the configuration page for all network settings from operational panel and check all network settings.
I hope this help you | | | |
| |
3 Weeks Ago
|
#7 (permalink)
| | Vacuum Cleaning Expert 500+ Posts
Join Date: Mar 2008 Location: File not found
Posts: 827
Rep Power: 12  | | Quote: | | | | | | | | | As alternative you can use SmartDeviceMonitor for Admin.
1. Maybe SSL activated on MFP? In this case use httpS://<ip address>
2. Maybe somebody chanched the access control range? In this case you can access on MFP by telnet by command "access"
You must print the configuration page for all network settings from operational panel and check all network settings.
I hope this help you | | | | | Aaagh no, didnīt you understand what he wrote: WIM is the only thing he canīt access. 404 page not found. | | |
__________________________ We can all Win, but at the end we all loose. Save the greyhound |
| |
3 Weeks Ago
|
#8 (permalink)
| | Trusted Tech 50+ Posts
Join Date: Feb 2009 Location: Toronto
Posts: 54
Rep Power: 2  | | Quote: | | | Originally Posted by iMind | | | | | | there are two boards B880-5171 GDI Nob
B880-5172 GDI basic
GW board on the spf is B284-5150 so there are three boards the last one is a SPF so that one my be out of question.
found this on the net:
"With GDI or GW controller model. For USA/Europe basic model. Version. Program No. Effective Date .... B8665171E or later PCB:KC3-S:GDI-NOB:ASS'Y ..." | | | | | Thanks "Imind", I guess I thought about trying to swap boards between machines to try and isolate the issue, so I'll give that a try. But I suppose if that's what the problem is, I may not want to invest in one of those to solve this 'minor' problem. As for the second part of our answer..." GDI or GW controller...." I'm not sure what you're referring to. I believe you mean
the latest firmware, but that has all been updated. | | | |
| |
3 Weeks Ago
|
#9 (permalink)
| | Technician
Join Date: Oct 2009 Location: Kyiv
Posts: 13
Rep Power: 1  | | Quote: | | | Originally Posted by iMind | | | | | | Aaagh no, didnīt you understand what he wrote: WIM is the only thing he canīt access. 404 page not found. | | | | | I meant this - port 80 (8080) on MFP is closed. | | | |
| |
3 Weeks Ago
|
#10 (permalink)
| | Trusted Tech 50+ Posts
Join Date: Feb 2009 Location: Toronto
Posts: 54
Rep Power: 2  | Thanks for the advice guys, they did help to point me in the right direction.
I have a lot to learn about "authentication", and privileges on these newer machines, but i learned a lot today.
I printed out the network I/F settings page and realized that security was set to "custom". I determined that this MUST be my problem; however I couldn't get into the "Network Security level" feature to change it. It saind "Privileges were required". this is when i did some reading on Authentication, etc. Even though it was not currently enabled, settings must have been made at some point and then the feature was disabled. I needed to Re-enable authentication, login as Administrator, then change the security settings to "0", then logout, and turn authentication "off" again, and VOILA!
Maybe this discussion will help someone else out of a jam.
Thanks again for the tips. | | | |
| | | Thread Tools | | | | Display Modes | Linear Mode |
Posting Rules
| You may not post new threads You may not post replies You may not post attachments You may not edit your posts HTML code is Off | | | All times are GMT +1. The time now is 08:19 AM. | | |