Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 5 of 5
  1. #1
    Field Supervisor 500+ Posts
    Ricoh CL7200/Simulations


    Join Date
    Mar 2007
    Location
    Brooklyn
    Posts
    512
    Rep Power
    27

    Ricoh CL7200/Simulations

    HI,
    Could you tell me procedure to enter simulations so I can reset Change Fuser Message?
    THANKS, ANDY


  2. #2
    Nurse Ratched of Repair 250+ Posts KopyKat's Avatar
    Join Date
    Nov 2008
    Posts
    367
    Rep Power
    22
    Engine - 7804 016 Fusing [PM Counter Reset]

    Starting SP Mode
    Start the service program mode as shown in procedure A or B.
    NOTE: The printer goes offline status while the service program mode is used.
    A: When the main power switch is off
    1. Push the on-line key [A] and the escape key [B] and hold them down.
    2. Turn on the main power switch.
    3. Hold the keys until the message “SYSTEM ver X.XX” is shown (where X.XX is
    the firmware version).
    B: When the main power switch is on
    1. Push the up arrow key [C] and down key [D] together for 5 seconds or more.
    2. Push the enter key. The message “SYSTEM ver X.XX” is shown (where X.XX
    is the firmware version).

    Selecting a Service Program
    1. Use the up arrow key or the down arrow key to use one of these:
    • 1. Service: Gets access to the Controller Service Mode
    • 2. Engine: Gets access to the Engine Service Mode
    • 3: End: Goes out of the SP Mode
    2. Push the enter key [E].
    3. Use the up arrow key or the down arrow key to find the necessary service
    program.
    4. Push the enter key.
    5. To go back to step 1, push the escape key one or more times.
    Changing a Setting
    1. Start a service program (Selecting a Service Program). The current setting is shown.
    2. Push the up arrow key or the down arrow key to input a value.
    3. Push the enter key. The setting is changed.
    NOTE: The setting does not change if you do not push the enter key.
    To enable some settings, you must turn the main power switch off and on
    (Enabling Settings).
    Quitting SP Mode
    1. Push the escape key one or more times until one of these is shown
    • 1. Service
    • 2. Engine
    2. Push the up arrow key or the down arrow key until this is shown:
    • 3: End
    3. Push the enter key.


  3. #3
    Field Supervisor 500+ Posts
    Ricoh CL7200/Simulations


    Join Date
    Mar 2007
    Location
    Brooklyn
    Posts
    512
    Rep Power
    27

    Ricoh Cl 7200/RESET

    Hi,
    Thanks for quick response.
    ANDY


  4. #4
    Field Supervisor 500+ Posts
    Ricoh CL7200/Simulations


    Join Date
    Mar 2007
    Location
    Brooklyn
    Posts
    512
    Rep Power
    27

    Ricoh cl 7200 Fuser Reset.

    Hi,
    Thanks for directing me to thread.
    Andy


  5. #5
    Junior Member
    Join Date
    Aug 2015
    Location
    Dunedin, Fl.
    Posts
    2
    Rep Power
    0

    Re: Ricoh CL7200/Simulations

    Hey this save my life. am a newbie and first post answered quickly.
    Quote Originally Posted by KopyKat View Post
    Engine - 7804 016 Fusing [PM Counter Reset]

    Starting SP Mode
    Start the service program mode as shown in procedure A or B.
    NOTE: The printer goes offline status while the service program mode is used.
    A: When the main power switch is off
    1. Push the on-line key [A] and the escape key [B] and hold them down.
    2. Turn on the main power switch.
    3. Hold the keys until the message “SYSTEM ver X.XX” is shown (where X.XX is
    the firmware version).
    B: When the main power switch is on
    1. Push the up arrow key [C] and down key [D] together for 5 seconds or more.
    2. Push the enter key. The message “SYSTEM ver X.XX” is shown (where X.XX
    is the firmware version).

    Selecting a Service Program
    1. Use the up arrow key or the down arrow key to use one of these:
    • 1. Service: Gets access to the Controller Service Mode
    • 2. Engine: Gets access to the Engine Service Mode
    • 3: End: Goes out of the SP Mode
    2. Push the enter key [E].
    3. Use the up arrow key or the down arrow key to find the necessary service
    program.
    4. Push the enter key.
    5. To go back to step 1, push the escape key one or more times.
    Changing a Setting
    1. Start a service program (Selecting a Service Program). The current setting is shown.
    2. Push the up arrow key or the down arrow key to input a value.
    3. Push the enter key. The setting is changed.
    NOTE: The setting does not change if you do not push the enter key.
    To enable some settings, you must turn the main power switch off and on
    (Enabling Settings).
    Quitting SP Mode
    1. Push the escape key one or more times until one of these is shown
    • 1. Service
    • 2. Engine
    2. Push the up arrow key or the down arrow key until this is shown:
    • 3: End
    3. Push the enter key.



Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here