Page 1 of 2 12 LastLast
Results 1 to 10 of 19
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Dec 2009
    Location
    Skopje-MACEDONIA
    Posts
    54
    Rep Power
    0

    Ricoh MP CW2200SP close front cover problem

    HI, On a NEW MP CW2200SP after 4-6 prints after instalation, the mashine give me an paper jam and after removing paper still stays CLOSE FRONT DOOR. I chek the left and right switches with instrument and they working fine. In INPUT chek shows the left ( double ) switch is open. I chek also the wires from the switches to the board, they are fine too.
    Any suggestions PLS?

  2. #2
    Trusted Tech 50+ Posts Comatose's Avatar
    Join Date
    Jul 2010
    Posts
    70
    Rep Power
    28

    Re: Ricoh MP CW2200SP close front cover problem

    Sounds like a faulty switch if input is showing them open. Try removing switch and use a paperclip to close the circuit on the connector to test if it is the switch or not.

  3. #3
    Trusted Tech 50+ Posts
    Join Date
    Dec 2009
    Location
    Skopje-MACEDONIA
    Posts
    54
    Rep Power
    0

    Re: Ricoh MP CW2200SP close front cover problem

    TNX for trying to help me. I replace the switch-es, chek the cabless ( harness ) with instrument, then short-wire directly to the pins of the board and still the same sympthoms: Close Front Cover. Any new suggestions PLS?

  4. #4
    Professional Moron 2,500+ Posts TonerMunkeh's Avatar
    Join Date
    Apr 2008
    Location
    Shitsville, UK
    Posts
    3,852
    Rep Power
    108

    Re: Ricoh MP CW2200SP close front cover problem

    Next step would be to check the service manual for blown fuse conditions, maybe a fuse on the PSU has popped. Were any options added at PDI, i.e. another roll drawer? Could there be a pinched harness somewhere?
    It's 106 miles to Chicago. We've got a full tank of gas, half a pack of cigarettes, it's dark and we're wearing sunglasses.

    Hit it.

  5. #5
    Field Supervisor 500+ Posts Exok's Avatar
    Join Date
    Jun 2011
    Location
    Edison, NJ
    Posts
    750
    Rep Power
    39

    Re: Ricoh MP CW2200SP close front cover problem

    If your switch is good, harness is good. Replace the board that the switch connects to.

  6. #6
    Trusted Tech 50+ Posts
    Join Date
    May 2011
    Location
    cleveland
    Posts
    78
    Rep Power
    27

    Re: Ricoh MP CW2200SP close front cover problem

    Quote Originally Posted by zoran.riko View Post
    HI, On a NEW MP CW2200SP after 4-6 prints after instalation, the mashine give me an paper jam and after removing paper still stays CLOSE FRONT DOOR. I chek the left and right switches with instrument and they working fine. In INPUT chek shows the left ( double ) switch is open. I chek also the wires from the switches to the board, they are fine too.
    Any suggestions PLS?
    Sorry cant help you out. But have you ever had a 672-01? and I cant get into sp mode/ Thx

  7. #7
    Retired 10,000+ Posts
    Ricoh MP CW2200SP close front cover problem

    slimslob's Avatar
    Join Date
    May 2013
    Location
    Bakersfield, CA
    Posts
    34,131
    Rep Power
    989

    Re: Ricoh MP CW2200SP close front cover problem

    Quote Originally Posted by zoran.riko View Post
    HI, On a NEW MP CW2200SP after 4-6 prints after instalation, the mashine give me an paper jam and after removing paper still stays CLOSE FRONT DOOR. I chek the left and right switches with instrument and they working fine. In INPUT chek shows the left ( double ) switch is open. I chek also the wires from the switches to the board, they are fine too.
    Any suggestions PLS?
    If this started happening immediately after installing, you may have a board defect that should be replaced by Ricoh under new machine warranty.

  8. #8
    Not a service manager 2,500+ Posts Iowatech's Avatar
    Join Date
    Dec 2009
    Location
    Iowa
    Posts
    3,933
    Rep Power
    97

    Re: Ricoh MP CW2200SP close front cover problem

    I'm kind of curious if the actuator for the interlock is OK.
    It probably is I guess.

  9. #9
    It's not easy being green 1,000+ Posts Cipher's Avatar
    Join Date
    May 2006
    Posts
    1,309
    Rep Power
    57

    Re: Ricoh MP CW2200SP close front cover problem

    Pray it has nothing to do with RTB30.

  10. #10
    Service Manager 5,000+ Posts
    Ricoh MP CW2200SP close front cover problem

    copier tech's Avatar
    Join Date
    Jan 2014
    Location
    London
    Posts
    7,531
    Rep Power
    182

    Re: Ricoh MP CW2200SP close front cover problem

    Is this is a brand new machine can you swap it out DOA with Ricoh or your supplier?
    Let us eat, drink, and be merry, because tomorrow we may die!

    For all your firmware & service manual needs please visit us at:

    www.copierfirmware.co.uk - www.printerfirmware.co.uk




Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here