Page 1 of 2 12 LastLast
Results 1 to 10 of 19
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Dec 2009
    Location
    Skopje-MACEDONIA
    Posts
    54
    Post Thanks / Like
    Rep Power
    0

    Ricoh MP CW2200SP close front cover problem

    HI, On a NEW MP CW2200SP after 4-6 prints after instalation, the mashine give me an paper jam and after removing paper still stays CLOSE FRONT DOOR. I chek the left and right switches with instrument and they working fine. In INPUT chek shows the left ( double ) switch is open. I chek also the wires from the switches to the board, they are fine too.
    Any suggestions PLS?


  2. #2
    Trusted Tech 50+ Posts Comatose's Avatar
    Join Date
    Jul 2010
    Posts
    70
    Post Thanks / Like
    Rep Power
    14

    Re: Ricoh MP CW2200SP close front cover problem

    Sounds like a faulty switch if input is showing them open. Try removing switch and use a paperclip to close the circuit on the connector to test if it is the switch or not.


  3. #3
    Trusted Tech 50+ Posts
    Join Date
    Dec 2009
    Location
    Skopje-MACEDONIA
    Posts
    54
    Post Thanks / Like
    Rep Power
    0

    Re: Ricoh MP CW2200SP close front cover problem

    TNX for trying to help me. I replace the switch-es, chek the cabless ( harness ) with instrument, then short-wire directly to the pins of the board and still the same sympthoms: Close Front Cover. Any new suggestions PLS?


  4. #4
    Field Supervisor 2,500+ Posts TonerMunkeh's Avatar
    Join Date
    Apr 2008
    Posts
    3,143
    Post Thanks / Like
    Rep Power
    69

    Re: Ricoh MP CW2200SP close front cover problem

    Next step would be to check the service manual for blown fuse conditions, maybe a fuse on the PSU has popped. Were any options added at PDI, i.e. another roll drawer? Could there be a pinched harness somewhere?

    Computers are serious tools, Michael!

  5. #5
    Field Supervisor 500+ Posts Exok's Avatar
    Join Date
    Jun 2011
    Location
    Edison, NJ
    Posts
    726
    Post Thanks / Like
    Rep Power
    26

    Re: Ricoh MP CW2200SP close front cover problem

    If your switch is good, harness is good. Replace the board that the switch connects to.


  6. #6
    Trusted Tech 50+ Posts
    Join Date
    May 2011
    Location
    cleveland
    Posts
    55
    Post Thanks / Like
    Rep Power
    13

    Re: Ricoh MP CW2200SP close front cover problem

    Quote Originally Posted by zoran.riko View Post
    HI, On a NEW MP CW2200SP after 4-6 prints after instalation, the mashine give me an paper jam and after removing paper still stays CLOSE FRONT DOOR. I chek the left and right switches with instrument and they working fine. In INPUT chek shows the left ( double ) switch is open. I chek also the wires from the switches to the board, they are fine too.
    Any suggestions PLS?
    Sorry cant help you out. But have you ever had a 672-01? and I cant get into sp mode/ Thx


  7. #7
    Field Supervisor 5,000+ Posts slimslob's Avatar
    Join Date
    May 2013
    Location
    Bakersfield, CA
    Posts
    6,239
    Post Thanks / Like
    Rep Power
    137

    Re: Ricoh MP CW2200SP close front cover problem

    Quote Originally Posted by zoran.riko View Post
    HI, On a NEW MP CW2200SP after 4-6 prints after instalation, the mashine give me an paper jam and after removing paper still stays CLOSE FRONT DOOR. I chek the left and right switches with instrument and they working fine. In INPUT chek shows the left ( double ) switch is open. I chek also the wires from the switches to the board, they are fine too.
    Any suggestions PLS?
    If this started happening immediately after installing, you may have a board defect that should be replaced by Ricoh under new machine warranty.


  8. #8
    Just a fellow wanderer 2,500+ Posts Iowatech's Avatar
    Join Date
    Dec 2009
    Location
    Iowa
    Posts
    3,733
    Post Thanks / Like
    Rep Power
    79

    Re: Ricoh MP CW2200SP close front cover problem

    I'm kind of curious if the actuator for the interlock is OK.
    It probably is I guess.


  9. #9
    It's not easy being green 1,000+ Posts Cipher's Avatar
    Join Date
    May 2006
    Posts
    1,101
    Post Thanks / Like
    Rep Power
    37

    Re: Ricoh MP CW2200SP close front cover problem

    Pray it has nothing to do with RTB30.


  10. #10
    Field Service Engineer 1,000+ Posts


    copier tech's Avatar
    Join Date
    Jan 2014
    Location
    London
    Posts
    1,847
    Post Thanks / Like
    Rep Power
    34

    Re: Ricoh MP CW2200SP close front cover problem

    Is this is a brand new machine can you swap it out DOA with Ricoh or your supplier?

    Let us eat, drink, and be merry, because tomorrow we may die!

    www.copierfirmware.co.uk

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here