Page 1 of 2 12 LastLast
Results 1 to 10 of 13
  1. #1
    Field Supervisor 500+ Posts



    Join Date
    Aug 2007
    Location
    Brooklyn
    Posts
    814
    Post Thanks / Like
    Rep Power
    23

    Thumbs up SCX-6200fx " over heat error cycle power" message

    Replaced fuser and get same message. Is this a common issue on similar Samsung models like clx6200series. Is this more likely a power supply problem? Customer says he can make copies but not print. machine goes into read then displays message. I have SM for CLX-6200 which uses some of same parts including fuser unit. I don't have parts in stock and don't want to order anything else expensive without getting advice first Any help is greatly appreciated. Frank/ActionPhotocopy


  2. #2
    AutoMajical Resolutionist 1,000+ Posts


    Tonerbomb's Avatar
    Join Date
    Feb 2005
    Location
    Bugaha
    Posts
    1,866
    Post Thanks / Like
    Rep Power
    57

    Re: SCX-6200fx " over heat error cycle power" message

    Quote Originally Posted by axyun View Post
    Replaced fuser and get same message. Is this a common issue on similar Samsung models like clx6200series. Is this more likely a power supply problem? Customer says he can make copies but not print. machine goes into read then displays message. I have SM for CLX-6200 which uses some of same parts including fuser unit. I don't have parts in stock and don't want to order anything else expensive without getting advice first Any help is greatly appreciated. Frank/ActionPhotocopy
    I hav'nt had this be a common problem with clx-62xx models. Normally the fuser would fix this. Make sure the firmware is current as Samsung does alot of firmware changes. DId you try a full memory clear?? this seems to fix random wierd things on the sammy's.

    Mystic Crystal Revelations

  3. #3
    Field Supervisor 500+ Posts



    Join Date
    Aug 2007
    Location
    Brooklyn
    Posts
    814
    Post Thanks / Like
    Rep Power
    23

    Thumbs up Re: SCX-6200fx " over heat error cycle power" message

    Thank you.I didn't do a memory clear as I am always reluctant to do that. Maybe i should have. I have minimal experience on these Samsungs and I am really ignorant when it comes to things like updating firmware. Not aware of how to do it. Will check manual. Frank


  4. #4
    Trusted Tech 50+ Posts


    mrizer's Avatar
    Join Date
    Mar 2009
    Location
    Alexandria, VA
    Posts
    61
    Post Thanks / Like
    Rep Power
    0

    Re: SCX-6200fx " over heat error cycle power" message

    Quote Originally Posted by axyun View Post
    ...Customer says he can make copies but not print. machine goes into read then displays message...
    What do you mean by make copies but not print? If you had a overheat error, it shouldn't let you print either. Maybe they can scan, but not print/copy???


  5. #5
    Field Supervisor 500+ Posts



    Join Date
    Aug 2007
    Location
    Brooklyn
    Posts
    814
    Post Thanks / Like
    Rep Power
    23

    Thumbs up Re: SCX-6200fx " over heat error cycle power" message

    The customer stated that he could make copies and scan but could not print a job from computer. The machine goes into ready and shortly thereafter shows message "overheat error. Cycle power". I tried changing fuser but got same message. I cleared memory but still same message. I am thinking it may be bad power supply. Frank


  6. #6
    Trusted Tech 50+ Posts


    mrizer's Avatar
    Join Date
    Mar 2009
    Location
    Alexandria, VA
    Posts
    61
    Post Thanks / Like
    Rep Power
    0

    Re: SCX-6200fx " over heat error cycle power" message

    If it can make a copy, then the machine must be mechanically fine. Whether the machine is copying or printing, it is the same process. That means the problem must be between the computer and the main board (which is also the engine controller). Try installing another computer directly to it, or replace the main board.


  7. #7
    Senior member of CRS 1,000+ Posts


    ZOOTECH's Avatar
    Join Date
    Jul 2007
    Location
    Insane Diego, CA
    Posts
    2,025
    Post Thanks / Like
    Rep Power
    56

    Re: SCX-6200fx " over heat error cycle power" message

    Quote Originally Posted by axyun View Post
    The customer stated that he could make copies and scan but could not print a job from computer. The machine goes into ready and shortly thereafter shows message "overheat error. Cycle power". I tried changing fuser but got same message. I cleared memory but still same message. I am thinking it may be bad power supply. Frank
    Have the customer turn off "Enable Bi-directional Support" to see if he can print.

    "You can't trust your eyes, if your mind is out of focus" --
    Sometimes, I feel like an island in a sea of incompetence. (.,.)
    "Work to live, don't live to work"

  8. #8
    Field Supervisor 500+ Posts



    Join Date
    Aug 2007
    Location
    Brooklyn
    Posts
    814
    Post Thanks / Like
    Rep Power
    23

    Thumbs up Re: SCX-6200fx " over heat error cycle power" message

    Thanks for the input guys. Frank


  9. #9
    Master Of The Obvious 5,000+ Posts


    blackcat4866's Avatar
    Join Date
    Jul 2007
    Location
    Lapeer, Michigan
    Posts
    10,881
    Post Thanks / Like
    Rep Power
    163

    Re: SCX-6200fx " over heat error cycle power" message

    Quote Originally Posted by axyun View Post
    ... I didn't do a memory clear as I am always reluctant to do that ... Frank
    I happen to agree with this philosophy. I rarely fixes anything, and often creates additional problems ... like defaulting the display language to Portuguese. At least it's a problem for me.

    The power supply is another possible cause for fuser errors. Personally, I think that the customers observations are incorrect. Printing and copying should produce the exact same error. =^..^=

    If you'd like a serious answer to your request:
    1) demonstrate that you've read the manual
    2) demonstrate that you made some attempt to fix it.


    blackcat: Master Of The Obvious =^..^=

  10. #10
    Field Supervisor 500+ Posts



    Join Date
    Aug 2007
    Location
    Brooklyn
    Posts
    814
    Post Thanks / Like
    Rep Power
    23

    Re: SCX-6200fx " over heat error cycle power" message

    I think that the customer was saying that although there is an error message he is still able to make copies but the machine will not print from computer while in error condition. I did not test by making copy but just assumed what he said was true. Frank


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here