Search:

Thanks for the replies so far, well, most of them.
Raplma, where are you in the UK? I know a guy who is frequently going backwards and forwards, maybe we could work something out. What would the...

Hi,
It's time to get rid of the Bizhub. The main unit needs work, most consumables are over their 100% and it's throwing an error code on startup. It also has the big feeder, relay unit, folder,...

New fiery software installed and the RIP is working again.
Can't thank Synthohol enough for all his perseverance and help with troubleshooting my issue. I hope to be able to help someone else as...

There have been further developments.
Unfortunately, someone else has been into the system to attempt to fix it. They apparently ran one of windows wizards and this has now bricked the Fiery.
I...

I have tried reversing the SCSI cable, checking the board is seated correctly in the Fiery, taking the back off the hub to inspect the connection there, seems like it's straight on to the mobo and...

Is it me or are my screenshots miniscule?

Blank password - refused.
I have no access to the direct queue.
Controller tab is greyed out.
Launched internet explorer on the Fiery via RDP and can type the router address in and access the...

Hi Synth,
Right, I can ping the fiery but when I type the same into chrome I get a connection refused error.
I have tried and failed to print the network config from the bizhub, where I notice that...

Hi Synth,
Fantastic, I can almost smell the toner.
All I need to know now is, where is this web page you speak of? I have had a look around the EFI site but didn't see it. I also assume that I need...

I'll try to explain a bit more so you know the limit of my prowess with this beast.
I bought the machine as a second user C6500 with lots of finishing units and an IC303 Fiery.

After building it...

I've made a little progress.

I started by trying to run the following commands from an elevated command prompt:


sc.exe config lanmanworkstation depend= bowser/mrxsmb10/nsi

sc.exe config...

Thanks for the further replies to my dilemma.
Allan, I would imagine the bios is protected, there doesn't appear to be an option to start the bios editor on boot.
Synth, to answer some of your...

While I'm here, if anybody can help me to get the fiery back online I would be eternally grateful and paypal your favourite bar with the price of your preferred tipple.

When I remote desktop to...

Thanks for all your help guys.
For reference, it seems that the second LAN port is exactly that. I connected to it and then checked in the router and there it was with its own IP. I logged in with...

Thanks Synth, I'll give that a go first thing in the morning.
For some reason there's an empty RJ45 hanging out of that port, hope that doesn't bode bad.

I was wondering what the worst thing you...

OK, here's the story; I was having problems connecting to the Fiery, it seemed that the software wasn't starting correctly. I don't have the disks to reinstall.
So I connected to the fiery using...

Cheers Monkeybum!
I was wondering what it did as that is exactly what happened, I was getting wrinkles on 170gsm glossy.

Ta.
Steve.

Apologies in advance for the lame question, but what does the sliding toggle (3 positions) do near the top of the fuser section, exit side?
I've tried looking in the manuals but not managed to find...

First off, I'm not a tech, just an optimistic end user.
The problem can be caused by a bit of crud somewhere causing an 'always on' situation. Try running a business card around the bezel to...

Well that issue appears to be resolved, thanks to Mikeena, empiru and arcadian for your advice.

I seem to have also sorted out the touchscreen issue, which appeared dead. I first found a...

Holy crap!
Just ran a couple of test prints and the lines have gone from the front! There are still very faint lines on the rear of the print though, which I'm now guessing may be a separate issue...

Hi Mike,
Vacced a horizontal section of the developing roller and it all looks uniform.
I fear we are heading towards the laser!

Cheers,
Steve.

Thanks for your input guys. Life just got considerably harder though.
I pulled out the ADU and took the cover off the fusing unit, the rollers and belt look clear, apart from a transverse scratch on...

Hi Mike,
Thanks for your input, much appreciated.
I have the 2nd upper transfer roller on order and it is due any day now, I think I will also order the lower roller today as it doesn't look...

Hi all,
I have a problem with black lines running in the feed direction of the print. There are a cluster of fine lines around the center of the page (SRA3) and one thicker line in the upper...