Search:

Yes, google it.... BUT...
the Fiery is a seperate PC/box that is attached to the device to control printing on a more advanced/professional level.
it has it's own software and firmware that is...

It sounds like someone has set up authentication/account track.

Try going into service mode and see if it has been activated.
This option is ONLY available with the optional hard drive. that...

Yes, and make sure the C500 is FULLY booted up before you boot up the Creo.
Also check the cable, the connecting on that model is not the most "reliable".

1. This is achieved with the Fiery by opening a port and allowing users to upload PDFs through the Web Browser or by activating the "print via email" option. You will find what you need by looking...

:eek:This is a VERY common ADOBE related issue.:eek:

In a nutshell InDesign is converting the affected area to process instead of a spot colour.
If you go to the Adobe sight they have many...

Yes, the alignment pages will ONLY work on the DEFAULT paper type and on a standard size. :rolleyes:
You can set the default type in Command Workstation under server settings.

Try ajusting the registration loop.

Where is it jamming?

Helpdesk | Konica Minolta Business Solutions CANADA

Look in the Pagescope software for the box operator utility it is FREE

What was the actual issue?

In the Feiry is a setting for the server... turn OFF convert paper sizes.

This is the server setup and you will need to reboot the server.

By whom?

They are considered assets by the bank and they will be looking to recover them.
Just because a compnay goes under does not mean that those items no longer have any value to the...

The Fiery has lost communication with the C500, try:

rebooting Fiery fully.
Check that the SCSI cable is properly seated
replace the cable

If it is still functioning then it is just an old...

Helpdesk | Konica Minolta Business Solutions CANADA

The packaging utilities are available via a link from the helpdesk website.
Thge link is labeled "Knowledge Base"

If you cannot find the...

Those products are registered somewhere.

As soon as the Serial numbers are submitted a red flag will come up.

Even though the dsealer went under the products are still part of the KM...

San to SMB is NOT support on that model due to the Feiry.

Use Fiery Remote Scan, use the TWAIN interface from within Acrobat to create a mulit page PDF file.

Rotate the sheet 90 degrees.
You need to grip it from theother side, most likely the 11" side.

OHP is not a standard stock and needs to be handled differently

Select cover in the booklet wizard and new options appear.

You can select to print on the cover as part of the book or select the PB Cover tray AFTER you select the cover as an insert.

If you...

WOA!

It sounds complicated at first....

You can create an overlay file in the driver by using the letterhead and then loading it into the driver. In therre you can specify where that overlay...

This is an older known/resolved issue with this model.
It is hardware related, if I remember correctly a "board" needs to be replaced in the MFP.
It is NOT a RIP/File issue.

Here is a link for a FREE tutorial kit form EFI on this very subject.
It is a very good tool with examples and templates.

http://www.efi.com/FreeFormKit/

The driver is actually stored on the ES-1000 itself.

If this does not work, then go to the Greytag Macbeth website and look for the I-1 Pro device.
It used to be spelled I-ONE.

Load it to a...

Things I would check on the C500
- Is the auto tray switch on?
- If it is, is tray 2 listed on the allowable trays
- if it is, move it up the list over tray 3
- are the media settings the same...

Sounds like a bad HArd Drive to me.

The BH200 is a low end BW Office MFP.
It only supports Scan to email, FTP, SMB, and the optional Hard Drive.

Interesting, thanks, I was not aware they also changed some of the feed rollers.


Things here at CourtneyPark are different, to say the least.
PKPB is GONE! :eek::p:D

Cut backs just in...