Search:

Type: Posts; User: bizhub1

Page 1 of 10 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    58
    Views
    13,891

    [Misc] Re: Bizhub C300i - Freezes during use

    Thank you
  2. Replies
    58
    Views
    13,891

    [Misc] Re: Bizhub C300i - Freezes during use

    Hello, I was wandering if you ever figured this out? I have one doing same exact thing. I have storage bd. On order. Thanks
  3. Replies
    2
    Views
    3,519

    Re: 4050 duplex jam

    Solenoid, we have replaced quite of few.
  4. Replies
    7
    Views
    704

    [CQ] Re: B601 Background

    I just had one do this, and changed softswitches and cleared right up. Changed sw 23-2 and 23-3 from 0 to 1. Also change 5-0 to 1
  5. Replies
    23
    Views
    14,241

    Re: c652 tray 3 jams

    Just an FYI, KM has a new ribbed pickup roller for these models. It is for the trays and the bypass tray. The new 654's are coming with it installed. The part# is A5C1562200. There is a tech bulletin...
  6. Replies
    8
    Views
    1,186

    Re: C6500 Fuser breaking gears

    my guess is the one way on the upper roller is on backwords.
  7. Replies
    4
    Views
    662

    Re: C652 Going dead on Pre drive

    Had one do the same thing and it was the power supply
  8. How do you do a Ghost image on a Ikon CPP 500 Creo rip and can you use a CPP 8050 Rip

    I'm trying to remember how to do a ghost image on a Ikon Creo Power Pro rip connected to a Ikon CPP 500. Will a Fiery meant for a CPP 8050 work?
  9. Replies
    9
    Views
    1,010

    [Misc] Re: Strange banding along the side

    How about make,model ?
  10. Re: C452 Paper entering FS526 finisher is buckling too much

    I had a 526 that buckled and jammed 11x17 paper going into the finisher and mine turned out to be the one way bearings in the transport unit. Might want to check
  11. Thread: C284 FREEZE

    by bizhub1
    Replies
    8
    Views
    1,604

    Re: C284 FREEZE

    Just had a 552 do the exact same thing, turned out bad ram on map board.
  12. Thread: IR 8070

    by bizhub1
    Replies
    3
    Views
    845

    Re: IR 8070

    It was the switching pcb.
  13. Thread: IR 8070

    by bizhub1
    Replies
    3
    Views
    845

    Re: IR 8070

    This is where I have turned it off on other machines, problem is, it is not showing up there.
  14. Thread: IR 8070

    by bizhub1
    Replies
    3
    Views
    845

    IR 8070

    Have a I R 8070 that has says limited function mode on control panel, and says stapler can't be used. Seen this on other machines but not a 8070. Anyone now how to clear or reset limited function?...
  15. Replies
    10
    Views
    1,996

    [Misc] Re: Fuser Rebuild Kit for C6500

    Don't know of any kit to rebuild fuser. There is a 100k and 200 k kit for that includes trans. Belt and rollers, etc. I believe all parts need to be ordered separately.
  16. Replies
    6
    Views
    896

    Re: konica minolta c650 fiery

    In service mode, change controller setting to 0
  17. [Misc] Re: Bizhub C224, address book email setting not avaialable

    If it is a 224e, they have been coming with scan to email turned off in the admin mode!
  18. Thread: OCR Software

    by bizhub1
    Replies
    5
    Views
    1,217

    Re: OCR Software

    Check out nuance
  19. Replies
    2
    Views
    722

    Re: Bizhub c364 drums

    You can also turn the warnings off right in service mode, no special firmware needed!
  20. Thread: C2636

    by bizhub1
    Replies
    1
    Views
    411

    C2636

    Hello, have a customer that is junking out there tired C2636 and wants me to pull the hard drive for them. Wandering if someone could give me a heads up where it is so I don't pull every cover...
  21. Thread: Non compete

    by bizhub1
    Replies
    3
    Views
    743

    Non compete

    Just wandering if companies are still making techs sign non-competes and if they hold up. Our company has been throwing around the idea. Never have had to sign one.
  22. Replies
    17
    Views
    65,531

    Re: Bizhub C654 w/error E301(not in manual)

    Are you sure it is not a C0301? If so that is a suction fan error.
  23. Replies
    8
    Views
    1,662

    Re: C452 account track

    Will give that a shot, firmware C5 and driver 3.6
  24. Replies
    8
    Views
    1,662

    Re: C452 account track

    No, can not get it to change to enabled. Hit the acquire settings tab and still no change
  25. Replies
    8
    Views
    1,662

    Re: C452 account track

    Those boxes are all checked, they were checked when the drivers were on the server also, but the pop up box will not come up on the xp computers. The windows7 computers work just fine
Results 1 to 25 of 231
Page 1 of 10 1 2 3 4