We have 3 Xerox AltaLink C8045 we just received from a store. They are all booting to these screens. Could anyone tell me how to reset these to factory default and clear these settings they had to...
Type: Posts; User: jmandassociates
We have 3 Xerox AltaLink C8045 we just received from a store. They are all booting to these screens. Could anyone tell me how to reset these to factory default and clear these settings they had to...
Anyone know how to get rid of this screen that comes on as soon as it boots up. It's a used machine we just got in and need to disable this card access.
51942
Anyone know where I can get the service and parts manuals for a Canon DX C5760i. The sites I usually buy the manuals on doesn't have this model.
We have a Ricoh Pro C5110s and the drawer unit not the paper drawers is stuck. It will only open about 1 inch then it stops. Any ideas what could be stopping it?
After we physically replace the NVM board is there anything else to do to set it up, reprogram it or anything?
Thanks. We tried to format the hard drive still the same error. We also checked the battery that was good. We ordered a new NVRAM board to try.
Looking for some help with a Xerox Color 570. As soon as you turn it on it says "Please Reboot 116-334" Rebooted multiple times and it didn't change. Thanks.
Working on 2 Xerox Color 570 we just got in both with problems. Previous owner kept the hard drives. We replaced them with 80GB sata hard drives we had laying around. Not sure if they need to be...
Looking for Xerox Coloe 570 service and parts manuals. Anyone have them or know where I can get them or buy them?
Anyone have any ideas. I haven't had any luck finding anything.
Trying to find the part # for the plastic piece in the picture that holds the other side of the spring on the ITB. I couldn't find it anywhere in the parts diagrams. The other picture is the other...
Looking for help with a Xerox Color 560. I am getting an 012-212 error with the finisher. Any help would be appreciated.
Looking for the Xerox Color 560 service and parts manuals. Most importantly the parts manuals. Any help would be appreciated.
We replaced the Paper Surface Sensor and did the ADF settings and it's still not raising the tray. Any other ideas?
Working on an IRADV C5030. It was getting an E000732-0001 scanner communication error. We replaced the reader controller PCB and that error went away. But now when I put a sheet of paper in the...
Need help with a Ricoh MP2550sp that the network just stopped working today on it. You can't access it's IP or print to it any more. The orange light is solid on the network jack but the green...
I actually just checked that yesterday and the lock is engaging and the arm is going in under the sensor. I even went into the service mode on the BK5010 and did a sensor check for that docking...
We tested the cable from the finisher to the BK for continuity and it tested fine. We sent the copier interface board from the BK and the main board from the finisher to get repaired and both tested...
We put everything back together and reseated all the connections on IOB 1, 2, BCU, IPU and the controller and the error went away. So it was just a loose connection somewhere. Thanks for all the...
Can anyone help me with a Canon IR Advance C9280 with error codes E000075-0002 and E000302-0001. For the E000302-0001 error we tried reseating the connections on the reader controller and the...
I haven't tried connecting with a crossover cable. How do you get into 1993 and the checksum. I don't see anything about it in the service manual.
Yes they tested them in another C901. Which boards should I check the LEDs on? Do they show you anywhere in the manual what LED should be coming on each board?
I sent the BCU and IOB 2 in to Hytech for repair and they said both boards tested fine. Is there any other board that could cause the error. We have reseated every connection on the BC, IOB1, IOB2,...
The only connection on the BCU/Engine board is on the back it plugs right into the IOB board, there aren't any cables or anything to it. I removed it, reconnected it, and just for the heck of it...
I'm not able to get into SP mode from that screen. Also which board is the Engine board. I have looked in the service manual and can not figure out which board it actually is.