I've now got a manual. There is only one laser unit. It's not the toners. I've stuck tape over the charge contact on both colours. Get solid colour, that rules out drum cartridge, transfer. Got to...
Type: Posts; User: Danwood007
I've now got a manual. There is only one laser unit. It's not the toners. I've stuck tape over the charge contact on both colours. Get solid colour, that rules out drum cartridge, transfer. Got to...
Hi. I've got a HP M552DN that has no yellow or magenta on the page. All cartridges show 100% and all are genuine HP. I've swapped cartridges with new out of packet. Still the same. Supplies status...
Well it can't be that for me. The boards have never been removed before
Hi. I've got a ricoh mp2501 throwing all sorts of issues at me. Stating photoconductor unit not set properly, at the same time as an sc144-00 and sc 992-00 error. I've seen a thread on here from 5...
Hello. Please help. I have this exact Sc144, sc992, set photo conductor properly fault. What exactly fixed it? Not entirely sure I understand the end message.
every thing said about these fusers are correct. I have about 50 6052ci mfps split over two sites. Every single one has been replaced under warranty, due to the wearing of the belt at the front and...
Thanks for this mate. Looked at this straight away, and found the board had blew. Cheers
Guaranteed it will be the sd card. Absolutely useless these machines. Have constant problems with the sd card in the mx 2314 machines. Terrible not to have a hdd
hi,
Ive got a several sharp mx2314NFX mfps situated over two sites for the same customer. My problem is that the customer complains that a couple of the devices stop printing and scanning. It seems...
ive powered on and off, ive removed and re installed the fuser assembly. I have not replaced the fuser unit as yet because it was only replaced two weeks ago. I was wondering if there was another...
hi,
ive got a xerox workcenre 7428 with a constant 010-328 error. fuser warm up error. The fuser unit was replaced a couple of weeks ago for the same error. The service manual does suggest that...
Hi. What was the out come of this? I have exactly the same problem
hi,
ive got to visit a bizhub c451tomorrow. Customer is saying that all prints and copies are blurred after a previous engineer had fitted an image transfer belt assembly and a secondary transfer...
Just to confirm. I replaced the non contact thermistor which fixed the problem.
Hi,
ive got a sharp mxm850 showing h2-00 error. Error relates to non contact thermistor open error. I've checked continuity of lamps and the two thermostats. Both fine. The connections of the fuser...
Hi,
I'm going to look at a colour cube 8570 tomorrow with error 99.023. I have no knowledge on this machine and no manuals. Could somebody please point me in the right direction. I know a...
thanks for replying...the machine is new, only done 36k. the paper looks ok , but I did notice the machine had non OM toner in it. ive attached a photo of the fault. as suspected , when I turned up...
hi. ive got an issue with the above model giving a grey shadowed background to copies. a previous engineer has been and said it was working fine when he went, so he calibrated the machine. now, a...
Hi,
I've got a job to do on a samsung scx4833fd. It says the tray 1 torque limiter has reached its life. I've downloaded the service manual, but cannot find the part number for the tray 1 torque...
hi.
i've got a sharp mxm850 stating "install developer cartridge blk".
I have lots of these machines in the field and have never seen this message before. it has been displaying this message on...
I think it's scan to email. But possibly scan to folder too.
Hi. I've not had any experience on this model before. I attended a Call where the machine was constantly turning off then on ,in a continuous loop. I disconnected the hdd which made the machine come...
Hi. I've got a cannon ir3045 with error code e000007-0000. Is this a case of just replacing the fixing unit? Or are there other causes for this? Also, could someone tell me the reset procedure for...
im getting error code L4-12 on a sharp mxc 310. Code relates to secondary transfer unit problem. Both the primary and secondary transfer units have recently been changed. Any ideas guys? thanks