Search:

Willing to pay for the pdf downloads for what I need. I bought this old copier (Canon IR3300) for personal use. During transport, the scanner assembly came apart. The scanner unit is sitting in there...

The problem was that it would not allow me to perform a logical format. I did run the physical format. I spoke with a guy that works on these bizhubs quite a bit, and he told me to try 1 -15 as the...

35333353343533535336

Always install with the IP address on a network. As far as smb (samba), you'll need to make sure the ports are open in the firewall on any workstation or server you want to scan to. Samba runs on TCP...

Is there a way to reset the HDD lock password is you do not know it? We bought a C220, which is pretty much the the same as a C360, and the drive failed. I replaced the drive, and it's giving me the...

Bought a used bizhub C220 and the HDD failed. I put in a new SATA drive, and it's asking me for the HDD lock code. Is there a default or work around code? Or how can I reset or remove the code if I...

I have a HP cm6030 throwing off a 30.01.40 error message. I have replaced the scb, the cpb, and the formatter board. I have checked all connections, and have updated the firmware to the newest...

I have a Canon IR C 3220 that keeps jamming at the rear of the machine. The photo below came out too small to see where I have it showing the jam, but I can send photos. Anyone have an idea of what I...

I had issues with Windows 7 connecting using smb, and fixed it with deleting out the credentials under control panel - credential manager. Then, create the new credential. Then, I applied the...

One other thing to try is if the copier has a ping utility, try pinging google.com or 74.125.224.72 to see if it goes through.

Instead of using IMAP, try POP3 settings on GMAIL. It would be the same settings used if setting up Outlook or Windows Mail. The SMTP settings are what send the mail. The POP or IMAP settings are...

Did you double check the SMTP settings against these e-mail services you're trying to use to make sure all settings match?

Also, I'm not familiar with the tool you used to set up a ftp server, but a good one for Windows that I like is Filezilla. If this is a Linux machine being used for the server, I like ProFTP as a ftp...

I know this may be basic advice, and you probably have already tried this, but make sure no firewall is blocking port 21 on the destination machine.

My church has an older Hitachi projector they bought new (and paid a ton of money for). It has a blue line that runs vertical on the left side of the screen. I have the case apart. I have read...

The copier tech never did show up, but I did finally figure out what the problem was. It was a setting for the paper size in the program was mismatched from the size of the paper on the copier. She...

Sorry, forgot to answer your question. It is printing directly to the printer.

Thank you for the help, and yes, I will reply with the outcome. Leaving in a little while to head that way. Again, thank you.

I'll take a look at that as well. Thank you.

I'll run that by him in the morning. Thanks for the help.

I had a lot of issues with scanning with a Lanier LD160C to a Linux server through Samba (SMB). I also had a tough time getting Windows 7 work stations to see the Linux server to get to the shares...

With Windows 7 - 64 bit, the Lanier site has either PCL5 or PCL6 listed for drivers as well as a universal driver. I'll try swapping out drivers in the morning and see if that gets me anywhere....

I have the PCL5 drivers installed. According to the copier tech, this model does not have postscript installed. That's another issue I'm trying to work around, as we have one Pastor that insists on...

Our church has a Lanier LD160C set up on a LAN. When printing a 11x17 document, duplex print, and requesting multiple copies on the print job, the print job goes through to the Lanier, but it only...