Hello, someone has experienced torubles with this error code?
i have tested NC thermistors with multimeter and it seems they are ok, i compared measurements with another fuser thermistors and i got...
Type: Posts; User: blax
Hello, someone has experienced torubles with this error code?
i have tested NC thermistors with multimeter and it seems they are ok, i compared measurements with another fuser thermistors and i got...
hello
someone know where is located paper size sensor on tray 5? detects only 12.8", and i need 13" width paper...
hello, in a XEROX WC7775, bypass tray 5 doesnt feed the sheet, only 375-135 error in fault history, inside tray 5 the motor gears are ok, also fuser lamps are ok... i tested with another fuser,...
hello, for a Wc7775 where can i find the paper size sensor to clean it? tray 1-2 detect wrong size of paper, i need open the tray several times, if i put 8.5x11" paper, sometimes detect smallest or...
HELLO
can someone tell me the difference between IU210 and IU310? i only found iu210 at stores in mexico and would like to place iu210 in a iu310 c352 machine... but i dont know if can work or only...
46475
someone know if 2nd BTR can do this? i replaced transfer belt cleaning blade but same results...
thanks!
thanks to all, i solved, i entered on service mode and failure was Y drum, the cleaning blade was stopping opc rotation, now its solved
i know itīs CYAN unit problem, but we open it again and cant find whatīs wrong inside...
Hello, today weīre cleaning CMY imaging units, then we got this error... itīs a XEROX WC7775
all copies do the same... even if i detach ic-406 controller...
distortion patterns should be a ram issue but not really cause i replaced all modules again...
Synthohol sent me fiery software and now i can print more than 1 file with new fiery system, but now i have a "new" problem... b/w copies or printings are ok... but color copies or color printings...
yes, please send me the software, thanks :)
nothing... all consumables are ok, without fiery the machine work so good... the problem is with fiery attached.
user image
i have removed fiery unit, cleaned inside and same issue.... cant print more than 1 file...
without fiery, the machine can print 2,5,10 files perfectly... so fiery is not working fine...
fiery...
yes, i h ave all materials to do service for the unit, i never opened the cabinet but you are right, this ic-406 was released on 2000-2002, so should have tons of dust inside. after a big clean,...
yes, i will contribute, no idea before about $$ avatar hehe until you said :)
and yes, i back the fiery to factory defaults, all files inside HDD were erased, and re-setup ip address ( i was...
error C4765
on lcd screen of c352 if i print more than 1 file, then appears the code involving extraction hardware timeout, that code referal about DIMM or board replacement, but i tried with another memmory...
i suspect is fiery ic406 module, but i dont know how to made a diagnosis of fiery
the problem is i only can print 1 print job, if i send more, command wordstation freezee, and emperon, shown error state...
any ideas?
i get the error on control panel lcd, machine can do copies, work fine with fiery remote scan, but 0 print pages from computer, was working fine but started to fail when just first page printed from...
i am getting: "printer is in an error state", i replaced DIMM modules from another machine, cleaned boards, and rough memory check is ok, but we can not solve it... any ideas?
machine have attached...
can you suggest compatible toner cartridges sold on precisionroller.com? or only original toner should guaranteethe best quality?
to "clean" the machine should i need follow this steps?
1.- remove cartridges with bad powder
2.- remove developer
3.- i have no idea