Thanks ADV Copier
Type: Posts; User: richwalker
Thanks ADV Copier
Good day fellow techs, looking for the service manuals for Riso CV180 & EZ220U. Thanks .
Good day fellow techs. I had the same issue with a BHC 658 last week. Thought I did the calibration correctly, but found out I didn't. I don't have the 658 manual, I have the 458 and up to c654e, so...
Good day EarthKMTech,
Thanks for this post as I have been going back and forth with a C654e with the same issue. The customer is way out of town and its a government office that is always...
Thanks for the tips guys. I disassembled the unit and found the cams and lever were dry and therefore harder to move up and down. I lubed them and all is well. Been working for a week now and...
QUOTE=khaled_abosere3@yahoo.com;437598]First: check the waste toner case for transfer belt unit it may blocked
Second: check pipe no.8 that as shown in following attached picture (pic.2) it may also...
Ok, I have the manuals on my laptop. Will check that. Thanks laitang.
Richwalker.
Thanks laitang. Now I know where to look for the sensor and what to look for to solve the problem.
Richwalker.
Hi all,
Have this BH c253 giving a c-2151 code. Checked the M-11 motor and it's connected ok. I'm trying to locate the ps-36 sensor, the manual ins't very helpful
. I reinstalled the transfer...
I agree with EarthKMTech, check the toner adding solenoid to ensure it's not sticking in the open position. If it is, then clean it and replace developer and run F8 again.
Richwalker.
Thanks all for the tips and suggestions. I bought a rebuilt unit online for less than 200. Got it 2 weeks ago and installed it in the C350 and it's all good now.
Thanks again for all the help.
...
Thanks blackcat4866, thought about that but wasn't sure if the connectors were a factor or not. I'll get the 220v unit and swap out the lamps as it's the thermistor that's broken on the unit.
...
Re: converting 220v c350 fuser to 120v fuser
If anyone has a used fuser (120v) that I can get/buy with the thermistors intact that would be great.
Richwalker.
If anyone has a used fuser (120v) that I can get/buy with the thermistors intact that would be great.
Richwalker.
Hi all,
Just checking if any of you brilliant techs have ever converted a 220v c350 fuser to be used in a 120v c350 mfp. I've got a customer that needs a fuser replaced and I've seen a couple of...
Thanks for the input Dag, I did some searching online and found some templates that I used to format my proposals with. Doing ok so far. Have a great day all.
Richwalker.
Hi all, I've started my own service business and I've got a proposal to do for a customer who would like me to supply them with 5 mfps for their company. They're currently using 2 Kyocera fs1035 to...
The lamp holder bracket on the MP 6001 has only 2 holes for the lamps. I know the MP 5500/6500 and 6001/7001 are similar, but if the unit you are rebuilding has a bracket with 3 holes, it's the wrong...
Customer got the toner and I installed and tested the machine. Still jams when doing LG. Checked closer and noticed the actuator for the adu transport sensor was warped and sticking in the up...
So I went and checked and cleaned the adf size sensor for LG and tested in simulation. Only now the mfp needs K toner so no printing until they get it. Hopefully the toner will be delivered by...
Thanks MHeon71, I thought about that as well, will check in there to see if a piece of paper or actuator is causing the jam. Just bewildered that it only happens when printing on legal paper, letter...
Hi all, I have a mx 3100n that jams when using LG paper. LT is fine. Jam code is APPD1-S, is this a case for updating the firmware? I cleaned the feed rollers, , switched the LG paper to another tray...
Had this on one of my training courses at KMBS, the harness that connects the control panel to the main pcb is disconnected.
Hope this helps,
Rich.
Hey Counsel, I'd say update the firmware for the engine and see if it helps any since the update for the finisher isn't out yet. Sounds like a timing malfunction though. I had one go coocoo on me...
Good day Pat, please find attached my resume.
Kind regards,
Richard Walker.