Change drum unit first, preferably get one from a working machine before you put a new one
Sent from my SM-N980F using Tapatalk
Type: Posts; User: NM0174
Change drum unit first, preferably get one from a working machine before you put a new one
Sent from my SM-N980F using Tapatalk
Hie
I managed to open the tonner hoper door with a credit card, but the tonner is stuck inside i couldn't pull it out.
I'm going back tomorrow to try again. Any ideas please share
Thanx
...
Hie all
I have the above problem as stated. The yellow tonner is finished but hopper door won't open. The manual tells me to try and turn the main motor using some tool which I do not have.
Those...
Hie all, I have a color machine showing that error code. Before you give me the RTFM which I probably deserve [emoji28] please help me from your experience. It's my first time with this model.
...
So I've cleaned the laser slit glass and still no change. I even removed the shutter and there's no difference. Not sure what else to try.
Any suggestions?
Sent from my SM-G965U using Tapatalk
Just realised that I didn't clean the laser. The tonner is not original but customer claims that's what they have been using since the machine was new. Meanwhile let me go over there and clean the...
So what was the problem? You didn't come back
Sent from my SM-G965U using Tapatalk
Hie all
I have a Canon IR1435 which is giving faint copies. I have changed the drum(which was making lines across print), fixing film, pressure roller, charge roller and cleaned out magnetic roller...
Replying message from 2018[emoji85][emoji85]
My bad, phone got damaged during that period and I lost comms for 3 months
This problem was on an IR2520. I eventually discovered that it was the drum...
Thank you very much, I stripped and cleaned the whole gear drive section, remounted the solenoid and the problem disappeared
Thank you for your help
Sent from my SM-G965U using Tapatalk
Thank you
I found the shaft broken so it's only now that I replaced it I'm beginning to get the noise and continuous feeding.
Let me check the solenoid mounting again
Sent from my SM-G965U...
Thank you
Is there a possibility that the solenoid itself gets faulty? It had tonner ako over then I cleaned it
Sent from my SM-G965U using Tapatalk
Hie all
I just changed the paper feed shaft on a Canon IR1435 and the machine now makes noise at the back and paper is feeding continuously when you switch the machine on.
Please help
Sent...
Thank you. Even if you take a drum and dev tank from a perfectly working machine. You still get the same copy with a background
Sent from my iPhone using Tapatalk
The copy comes out with a background as in the picture. Drum, dev tank and tonner are new. Please helphttps://uploads.tapatalk-cdn.com/20180328/92ca63e60f4991be97b40a18509cffb2.jpg
Sent from my...
The counter board is the correct one. When I change the counter board it gives me E0245. When I change the Boot Rom it gives me E0744-2000. When I put back the original things it just goes back to...
E0744-2000 is the full error code. The control panel boots up with the Canon logo appearing well with the loading bar appearing well. Then when its supposed to show the home screen thats when it...
Hie all
I have an error code E0744 on a IR2270 after i changed the Boot Rom. The reason for changing it was because the control panel would not show anything else except black "smudged" image....
Hie all
I have an RZ370EP that is giving an error code P89-350
I have checked in the manual i have but it is not listed.
Please help.
Hie all.
Is there a way to scan from an IR2520. I know of inserting on to Microsoft Office(2003 to 2010) clip art which I haven't been able to do on Ms Office 2013.
Please help
Hie all.
I have the above machine whose feed trays don't rise to the very top. When you put paper and close the trays, they rise but wont get to the top. only after switching the machine off and...
Meant to say "I can not pinpoint the fault on the unit itself".....
Hie all
I have the above machine showing E0747-5f02
The machine had its harnesses eaten by rats. we replaced them and the machine worked for 2 days before coming up with that error code. All I...
Thank you for your help. Sorry for being vague. (Machine giving me stress:o). I meant paper sizes. Its defaulting to "LTR" instead of "A4". I will go through the settings now and see what happens.
Hie all
Managed to upgrade the firmware and the error code is gone. Now i have this FNC-MODE appearing on the top corner of the screen and the sizes are out. How can i rectify that?