Thanks so much, Methogod.
That's really good news to hear. I have run any test yet, but I will certainly explore your 14x20 sheet size. I have the Stacked Drawers 4 & 5. So I guess I'll be trying...
Type: Posts; User: Topstep1
Thanks so much, Methogod.
That's really good news to hear. I have run any test yet, but I will certainly explore your 14x20 sheet size. I have the Stacked Drawers 4 & 5. So I guess I'll be trying...
Thanks Guys,
I'm gonna give it a try and report back my results so that others may benefit from knowing.
Thanks. I look at your PDF and translated some of the sizes to inches. NO 9x12 (which is a 12x18 sheet cut in half). I'd 'guess' any booklet maker would treat and staple it just like an 8.5x11; the...
Greetings,
Please tell me if the KM 6500 will accept 9x12 inch sheets in any drawer to make 5.5x8.5 Saddle Stitched Books with Bleed. I can run 8.5 x11s when a white border is ok but when Bleed...
Thanks to both you guys. I'll give it a try (and watch my fingers <smile>)
Hi my km6500 is coding and I want take the paper out of Draw 4 & 5. How can I open the draws with the Power off? Is There a Release switch somewhere?
thanks.
Got it. Thank you 'both'.
Greetings Friends,
Per chance, anyone have a KM C7000 Service Manual, I can read?
Kind Regards ...
Greetings Friends,
Per chance, anyone have a KM C7000 Service Manual, I can read?
Kind Regards
Good Morning, It anyone has any insight into my problem above, I am standing by and grateful for the share.
Hey guys. I am in an environment that likes the curing effect of 163-209 paper weight setting (higher heat than 81-105). The problem is the printer (fiery front end) does not like to Saddle...
Anyone know how to 'disable' or 'turn off' Color Management on a Rip using a Creo ColorServer?
I want make some custom ICC Profiles and before sending the targets, you have to disable ALL Color...
mulo_g,
I think that the info has to come from the Printer; The printers Serial No# and Printhead info is unique to each machine. So, the question I am holding out for (maybe someone can ask a...
Bupkis! I made no difference.
I decided to take a look (as if that will fix anything).
The main board has a battery on it. So I unplugged the printer and removed the Battery.
Probably the Reset I've been wanting. I'll leave...
Thanks for chiming in, Canuck. Yea the MC is 'much' cheaper. If I have to get in there, I will start with that.
You know, maybe we are taking the wrong approach here. Trying to use Technical...
2119821199
The Serial No. from the back of the machine is: AEF00824
Service mode show the CPU (empty) first and when I press LR Arrow, I see MC.
Look at what is in the MC. because it has the...
I think if you put a new Main Board in, there would be the same problem. Because, once you have installed it, the same screen that I am getting now would come up.
It wants the backup data (that...
>After replacement of the main controller PCB, the printer must be started up in the service mode to take over
the setting and adjustment values to the new PCB properly (the service mode will be...
https://www.box.com/s/sbm1h7unt3vawg1nk5an
Manual I've been reading from
From my Service Manual:
__________________
1. PCB replacement mode
This mode is used when replacing the main PCB or MC relay PCB.
By executing this mode,
- Backup data of the settings and...
Hi, I flashed the Printer already and while I was in there got the Log 2 log files;
Log files
https://www.box.com/s/ed0c6o1981edug0yqi1f
Normal Boot...
Does anyone know how the CPU board in a Canon IPF-6100 that has been cleared can be re-synced with the printer?
The command was issued from the front panel to replace the CPU by accident and now...
Hello Group,
I have a Canon IFP6100 when I turn it on says;
E196-404D (Machine ID mismatch between boards Check the main controller PCB.)
When I start in Service Mode it goes right to:
...