I've never uploaded an image before, hope this works. I didn't take a photo on site but attached is an image of another motor. I believe it's a rubber for shock absorbing? Its on every motor.
Type: Posts; User: MDR24
I've never uploaded an image before, hope this works. I didn't take a photo on site but attached is an image of another motor. I believe it's a rubber for shock absorbing? Its on every motor.
Hi all,
I attended a call last week for an MPC2004 giving intermittent SC120-00 (HP Error). After checking motors and sensors in engineers mode, checking drive belts, lubricating rails etc. I...
This is exactly what I was looking for thanks for the help everyone.
Hi all,
I've recently started working on Ricoh's from a Kyocera/Konica background. I've been having a play around in the service mode for a few different Ricoh models and was hoping if anyone...
RESOLVED
Original issue - When ID&PRINT is enabled the banner print option is disabled. Making it impossible to print banners whilst using id&print.
With the increase of customers worrying...
Hi rrrohan,
Just setup a print queue using the Generic Universal Driver V3.3. You were right when you go into "Settings" then "Administrator Customise" you can select the output method and have...
Thanks for the replies.
Allan, I think it has more to do with when banner mode is enabled it locks the queue out? So when ID&Print is enabled on the machine side it sees it as a compatibility...
Hi, has anyone tried doing banner printing whilst having ID&Print enabled? I just did an install at a school that requires User Authentification and ID&Print. But when id&print is enabled the banner...
I had this exact issue today on a 224E. The issue was, like yours it would say it was sent from the computer but when you get to the printer it would say deleted due to error.
Mine was due to the...
i dont think you can cancel sleep mode completely but you can max the timers for sleep/low power mode to 240mins. Its under the machine default tab in the system menu i believe.
We have only started to do the Konicas from C280 onwards so missed these
Easiest way to check if the fuser is registering as an old unit is by pressing utility and then consumable life. If it is...
Now whats the code your getting?
If the person you got your info from is correct and all your machine needs is a reset, there are 3 different ranks of machine reset Rank A,B and C. The rank...
If you want help you need to give the necessary information. Saying "you need to do a reset" isnt narrowing anything down.
Whats the model of the machine?
What error are you getting?
Help us,...
If you click the link from the previous post it takes you to the papercut website, once you're on there if you click the support tab it will direct you to the "knowledge base" it is extensive and can...
We haven't really touched the '1' range but as for the Taskalpards we had the issue from the low end Ta3050ci all the way up to the Ta8000i. We found that the rollers themselves could be changed...
I'd say try to reformat the memory stick using FAT32. Found that the Konica Minolta's seem to prefer that to the default FAT.
Have you done anything to fault find?
If you haven't already, I would start with swapping the Magenta drum with the Cyan to see if the fault transfers.
Good Luck.
No service manual explains it because you can't exchange those parts on the fuser. If you want a new roller you'll have to buy a whole fuser and replace it.
What firmware level is on the machine? have you installed the latest SSD firmware (v6.05)?
I know there was a fix for meter counts in the G20-J9 firmware, but that f/w is a few versions out of...
You can swap the drums around but you need to swap the chips. CMY have the same chips but the K chip is different. If you look on the bottom of the drums (front side) you'll see the chip.
The drive pack is definetley an issue! We've had this on the TA-8000i mainly because they have more volume but have some TA-5500i's do it also. The drive packs are exactly the same from the 45ppm to...
What machine is it? Admin isn't the login credentials of every kyocera machine depending on the Model it could be a different password/username. Are you trying to login using the web interface or on...
You got it right with 9272...
We dont have any of these machines out however the likes of the +3350 and +3110 require a reset procedure or for you to reboot the machine after a certain amount of...
dp770 feed problems - Topic
Knew I seen it before see post from this forum. The guy got the resolve.
The latest Firmware I can find is "TASKalfa_250_300_400_500ci_15.24.0010_(2013-12-20)"
Main FW 2H7_2F00.015.005 (NEW)