Search:

What life is your fixing film assy ? I replace mine about 300k but check for build up on the blade before this.. Are you using genuine toner also ? I would do both dev and drum if not..

I hads one today with 0207 code. The fuser was over life. Changed film assy . lower roller and lub'd lower bearings and bushes on delivery (orange roller ) job done. Normally get 300k out of film and...

Has this machine been modified with the ITB grounding plates ? It did cause marks at the bottom edge of copies/prints.....

Check what paper stock is programmed for that cassette. Heavy , plain ,recycled. Or if your sending a job check the paper size being sent.

I have had issues with these for image problems and it was a couple of things : 1 - replace the whole unit that the transfer roller sits in . This has been modified and you will get a slight fusing...

I would replace the ITB aasy and cleaner assy as a pair. I sure that the cleaner assy gets its drive from the ITB.

Before going too in depth I would check the following : 1 - Upgrade your firmware to the latest (MN6903/DC6501/FIN1501) - especially if you have inner finisher A1's. Make sure you select overwrite...

The problem is probably the registration / patch sensor assy that sits to the right of the black drum assy. They do get dirty and this will cause mis-reg. Clean them then do a full autograd , this...

Hi Chaps. I've got to visit a 2030 which one of my engineers if having issues with. Constant E003 error . New fixing assy put in and then DC con replaced. Previously machine had been showing constant...

In the east end and central london it is busy, and on the outskirts where the cycling is the roads will be closed on Wednesday. But it ain't been bad. Will get worse next week when the athletics...

It all depends if the customer is running Dept ID codes on the iRc2620. If they are she will have to put a code in when she prints regardless. getting rid of the system manager ID will not resolve...

There isn't a default on these. Go into sevice mode - function - clear - PWD - ok . This will clear the password so you can start again

Check the lifter cables in the deck. If they are not going up square then you will get this issue. Also sometimes the lift motor blows... but then you wouldnt get any lift at all.

Im the same as Canon Tech. On 3200's put them in before the drum does 200%. On these I tend to get E020 codes than leaking. On the 4580's put them in before 300% . These leak especially the black

That looks like hardened toner on the dev roller..... normally caused by generic toner ( which im used too !!! )

I had loads of E020 errors on these machines. After numerous visits it was the patch connection from the drum unit into the connections on the main frame. Apparently they stretch and lose voltage....

Its a J31 Jam. delay going into fuser. its had a new itb assy put in already and the copy quality is spot on. The machine is in a school so the summer break is near. Im debating whether to get KM UK...

Try these to start :


E732
Main cause The connector has poor contact. The reader controller PCB is faulty.
Mode of
Detection
0001 The main controller PCB has detected an error in the...

As Z said, check the internal sensor arms for paper burrs.. this happens alot on high volume machines. Also :

Check that your fuser bushes are on correctly ( both inside facing out ) and your...

Hi everyone. I've got a 250ci that giving me an in intermittant fault but regular enough for the customer to start getting annoyed !

it will jam at the 2nd transfer roller / registration assy.....

Looks like your losing transfer on the 2nd side. I would put a new trans/sep assy in firstly. You can go into option - body - and change the a setting that will adjust charge levels TR-SP-C1 to C5...

As previously mentioned by T.T , make sure that you update the firmware as this will resolve the timing issues giving you the FF90 jam.
DC 65.03
MN 69.01
FIN A1 15.01

DC has to be 60 + at...

Just a quick note on this one. The latest firmware on this is v13.0010 .

Thanks Canon Tec...... my thoughts exactly

Same as the other posts. Change the drum and the ITB cleaner blade. Don't forget to clean the patch sensor above the drum !