Hi All, been a while
I'm having an issue with a MP2555 where the last 1cm of the print (LEF) isn't fusing correctly and then deposits that bit of toner on the second page about an inch in from the...
Type: Posts; User: CableGuy
Hi All, been a while
I'm having an issue with a MP2555 where the last 1cm of the print (LEF) isn't fusing correctly and then deposits that bit of toner on the second page about an inch in from the...
Hi All
Does anyone know if a SPc431 fuser unit would work in a MPc300?
We're having an error of SC555. Thermistors have been replaced.
The price of the copier replacement unit is silly
Many...
Hi. Not sure that's the app I was thinking of. I'm talking about the one where you can do input/output checks on the screen from the app.
Not the one where you remote into the machine.
Cheers
Hi. Does anyone know how to add an app, the engine check app specifically. I've done it once since doing the training course back in Feb, but now it eludes me.
I have the app that was given to us...
Totally agree, but didn't fancy taking it apart a third time if there was still an issue. First time was to test for continuity. I did manage to knock the sensor out of the Toner recycling unit...
Hi. Just created a thread about one of these and their dirty habits. I replaced the drum shaft and bracket because the continuity between the Shaft and the earthing plate was pretty much non...
Hi All.
Been a while since my last visit here. Wanted to find out if anyone has had a problem with the drum shaft wearing out on this model at around 1.5mil. This has caused the machine to dump...
Hi All
I found the problem and only by chance really. I removed the duplex gate, which the bulletin suggests to clean up the pawls as the become rough. That's when I noticed that the return...
Hi All. Thanks for your suggestions. I've been to the customer over the last two mornings before everyone arrived and got the guy to print a couple of things. Here's what I found, it only makes...
Hi All
I'm having an ongoing issue with a Mp3053 creasing paper in the fusing exit area. No jams, just a crease or two down the centre of the page. All the fusing rollers have been replaced and...
Hi All
I'm having an ongoing issue with a Mp3053 creasing paper in the fusing exit area. No jams, just a crease or two down the centre of the page. All the fusing rollers have been replaced and...
Hi All. First post this year. Hope everyone is well.
I'm having an issue on a MP9002 where it seems to add excessive amounts of toner, eventually dumping toner in the pcu unit and on the page. ...
Hi All.
I have a Lexmark M3150 which for the most part is dead. This isn't the first time this machine has been on my bench with this problem. Earlier in the year I was called out because it was...
Hello everyone. First post this year, unfortunately it's on the pile of poo.....
I have a Mpc6501 which is kicking out Sc585 pretty much continuously, not every page, but enough to cause the...
I have one of these in the field. It's not a high volume machine, but I've been there 3 times since install to vacuum out the ledge on the PCU cradle. I went there today with the intension of doing...
Thanks Gift, Will take a look. It's just a pain trying to convince customers that the machine will work fine without changing it, especially the ITB.
Cheers
Sorry to Hi jack your thread, but on this subject can this be done for the 430's as well?
Or switch off the message that pops up on the screen on this model.
Customers don't buy the 'That Itb...
As many as they throw at me :D
Yes that's it, swap it with one you know is working to be sure
Not uncommon for toner hoppers augers(doesn't really have a pump as such) to foul up and not drive toner to the pcu.
good luck changing one of those... lots of fun :p
Clean the toner flow sensor. I've replaced pumps and had the fault continue, only to find the toner flow sensor dirty....
Think there is a bulletin out on this model were the exit sensor or the one before it goes faulty, can only be cured by replacing said sensor. Had a couple go in the field.
This is it...
...
Had a few go for no apparent reason, luck of the draw it seems
I've experienced toner marks on these models before and found it comes from a build up of toner and paper dust in the Transfer belt cleaning unit. It seems to be more prolific when customers are...
I've had one of these that used to spill it's yellow toner. I can't be certain if it was the machine or cartridge, but stripped the top side off and cleaned it up. It's seems to be ok now. Does it...