Sorry, no. As I have been retired for almost 4 years now, I can no longer supply manuals or firmware. A couple of years ago, I purged all of my work related information, both physical and digital.
Type: Posts; User: mrfixit51
Sorry, no. As I have been retired for almost 4 years now, I can no longer supply manuals or firmware. A couple of years ago, I purged all of my work related information, both physical and digital.
There are loads of contaminants in the waste toner, dust, dirt, paper talc, and such. If it were reintroduced into the developer assembly, the print quality would go down the drain, and expensive...
"2. How does that make him a jerk? Clearly, a lot of people wonder about this, I've been working on IT equipment for 17 years and I just discovered a waste toner box and wondered literally the same...
Just fought this a while back on an iRA6055. The registration sensor on that beasty uses a prismatic reflector, mine had been knocked out of place. Symptoms were exactly as you described.
It seems old threads do not die,, they just go into a coma! :)
Download Canon NP6317 Service Manual
The manual can be downloaded here. I would pay attention to chapter 10. The AE exposure
adjustment may get you where you want to be. Have not touched one of...
Thanks! I do from time to time check in, but do to a manager change,
(read you are not gainfully employed unless you are running around
with a screwdriver in your hand and your hair on fire...
Do you realize that the thread is almost 3 years old?
Best to jump into conversations that are current, instead of poking in the ashes...
As you seem to have covered all the mechanical bases, you might try clearing
DC-Con and re-entering your data.
BUT ONLY DO SO AFTER OBTAINING A P-PRINT OR LABEL PRINT!!
Failure to have those...
SST and the system software files are the only way to update this old girl...
What mikejose is referring to is only available in the imageRUNNER Advanced models.
I would suggest that you use conductive grease under that spring grounding plate on the shaft, better long term grounding, and no annoying "the copier is squeaking" service calls...
Most often I find the bushing (FC8-4479-020) that hold the bearings for the aluminum roller either bending under the spring pressure, or broken...
Firmware for these models do not utilize the SST. That is why they are not recognized when you tried to load them into SST. The files are executable, and launch a built in tool. This tool is referred...
Happy Birthday to you, Happy Birthday to you, Happy Birthday dear ( i have all of canon service+SST), Happy Birthday to you!!!!
You can either wish it apart, or grasp all the wires equally and keep on tugging...
You are welcome my friend,, I'm here to help when I can... :)
Print Controller Options
1. Multi-PDL Printer Kit-H1
When the imageRUNNER 7105/7095/7095 Printer/7086 devices are
configured with the optional Multi-PDL Printer Kit-H1, connected users can
access...
If your 3300 has an ethernet port on it, you should already have a print kit installed. Additional Functions, System Settings, Network settings. Input the IP and subnet numbers here to get it onto...
You are welcome :)
Me too,,, ran into a 2200 yesterday with the code, thought I would try the 1&9 start up. Started the process, walked out to my car, got the laptop, and the drive. Booted the laptop, I had to...
FC8-8828-000
Take two of these and call me in the morning...
These little adhesive plastic shims fit behind the rear paper guide and permanently set the rear guide in the LETTER position. 95%...
The picture you show does not represent the sponge noise dampening pad that was referred to above. The steel plate that forms the registration area has the reg sensor flag mounted to the back of it....
Best advice I can render is to not use reman'd drums. Savings is usually eaten up by flakey problems...
That size copier would typically see about 30,000 copies a month, doing the volume you are quoting puts it into the iR7095 range...
If the number of copies is as you say, it appears they have a pony doing the work of a draft horse...