Thanks for the help copyaction. I did the admin reset with blank password and it got me in. I was trying to change it before by putting a password in and it would not work. Thanks again.
Type: Posts; User: PEPELEMU
Thanks for the help copyaction. I did the admin reset with blank password and it got me in. I was trying to change it before by putting a password in and it would not work. Thanks again.
Heading there today and will check it out. Thank you. Will get back at end of day.
I am working on a ricoh 2550. Just installed used machine. Error is you do not have privileges when trying to setup network, scan to folder, and some other functions. Other than that the machine...
I have a ricoh aficio mp2550 copier. Trying to setup network scan and print. When I try it gives an error "you do not have privileges for this function" I have logged in as supervisor and blank...
Why is the hard drive braking frequently. That is not that common. There must be some other issue.
You can not just put a new hard drive in. You can buy the hard drive from hp with firmware already installed.
I am buying a Konica bizhub c220 from my used copier distributor and the machine has an error, no animation guide data available. I need to get the movie.exe file. I am not a konica dealer. I am a...
I am working on a Canon ir-3530. Needed a fuser unit was getting a E0001 error. Went back to replace fuser and turned machine on and get E00716-0010 erro. ????
I have a estudio 163 that is ghosting. Coming from the developer unit. Put in another machine and does same thing. Replaced mag roll same thing. Make multi copies and first page ghosting eventually...
Lunch is one knee on the steering wheel one hand holding the phone and the other hand jamming food in my face rushing to the next fire!!!!!
I am working on a canon ir-3530. The finisher is jamming. Paper exits out 3/4 of way and stops. I replaced the stack delivery slider ass'y which was broken and it still will not eject paper all the...
I had the same problem, updated firmware and still had problem, the changed the driver. If you are using pcl6 driver change it to pcl5. That is what fixed my problem.
Thank you Deep, That took care of the problem. I missed that step listed under adj mode and set mode 11 to 1 in service mode.
Thanks again.
I have a konica 7118 with a C03FF error code. I cleared memory service mode 11. And set code 12 to 1 for 18 page per minute machine and still comes back with same error.
Thank you
Hi Tia, Try using precision roller. They carry toshiba parts.
I am looking for info on error code E016 and E017 can not find paper jam and sensor test ok.
Thanks
John
Canon ir-3530 paper jams using the 2 bottom trays. top 2 trays work fine. The jam is on the right side right between the bottom 2 trays and the top 2 trays. The trays are set correctly. All new feed...
I am working on a ar-bc320 and when you put an original on the glass it will read 8 1/2 x 11, when you close the feeder it switches to 11 x 17. And you cannot feed from RADF. I tested the the...
Hi Kuby, So far the customer has not called back yet. Last time it happened it took about 2 weeks before it crashed. Thanks again. I will let you know if it errors again.
John
The heater switch was on. I switched it off and put a new HD in. Hopefully that was it.
Thank you
John
I am working on a IR-2800 with an error code E000602-0003. I have replaced the hard drive from my canon distributor. After 3 weeks the error came back. Ordered another hard drive from distributor...
I replaced the ground spring. The shutter is working perfect. I even held the shutter toward the front of the machine while running and still get the code.
Thanks
I have a canon ir-3530 that is getting an intermittant E110-002 error. I have replaced the laser unit, dc controller, middle feed ass'y. Checked interlock for laser shutter, reg roller ground. Any...
The drum blade #26NA-2090 BOTH MACHINES TAKE SAME BLADE.
Does any one have a scanner board and software for a konica 7020 copier for sale?
John