hi
thanks for your reply.
i ordered a new sep pad for tray 2 and its the same one as tray 1. the not the cork type, its the white sponge type.
ive got 2 sp5210's and 1 sp5200 at the same...
Type: Posts; User: ash_572
hi
thanks for your reply.
i ordered a new sep pad for tray 2 and its the same one as tray 1. the not the cork type, its the white sponge type.
ive got 2 sp5210's and 1 sp5200 at the same...
Hi
ive Removed the driven roller unit with 2 screws between tray 1 and tray 2 and there is no label stuck there and it’s clean. Also tray 2 is used for A4 plain paper so there no way labels could...
hi
ive been having this issue for a while now and cant seem to get to the bottom of it.
sp5210sf with a a tray 2 peripheral TK 1090.
jams from tray 2 every 4-5 pages with jam code 053 - T2...
I went back today to test from tray 2 and it still jammed double sided. Single sided I haven’t seen jam.
i also had a registration clutch that I went back with. I replaced the registration clutch...
thanks
i will give that a try when I go back soon.
1. I have only seeN it jam on duplex. Simplex runs ok.
2. I have not tried duplexing from another tray. The other tray is an a3.
i have the even log printed out should you require any more info....
hi
i have a kyocera taskalfa 3051ci that is jamming quite often with the jam codes of mainly 4011 and occasionally 0508. seems to be jamming when duplexing.
paper seems to stop before the...
Could also be the transfer belt worn.
Yes. In the end it was the pcb at the back of the device. Can’t remember what it was called. Check the ID sensor wiring connector on the board and reseat the connector.
Hi
i have cleaned the ID sensors and replaced the primary transfer belt and still the same. I will order some ID sensors
I have a sharp mx2640 with an error code of f2-78. colour registration is also out.
I have cleaned the ID sensors and replaced the transfer belt. colour density is very strong.
following...
Uploaded picture
I have already replaced the main drive unit. Thanks
Hi everyone. I have a mx3110 colour machine that’s making a vibrating noise. The vibration is nailing an impact on the colour copies with white lines in the image.
Black and white prints are...
To be honest I can’t remember. I must’ve changed the Patch sensors and changed the 2 colour drums it was affecting.
i would start with the solenoid assembly. I do remember changing them a few...
this machine has only done 10k. 8 months old machine.
E020-04A8-05 Toner Density Sensor (Bk) output error
Detection Description The output value of the Toner Density Sensor (Bk) in the Developing...
Yes. This also happens when I print off configuration reports.
i have the above machine jamming from tray 2 only. half of the page is out of the exit unit with no image on the document.
tray 2 pickup, feed and seperation rollers have been replaced.
tray is...
i am randomly getting error c6120 which is relating to the fuser over heating. we have replaced the fuser several times well within its lifespan and atleast once every few weeks we get this error.
...
Thanks for the info. I have removed the shutter and replaced the patch sensors (all 3). We shall see what happens. Should be ok without the patch shutter?
I have a strange fault on a c5250.
Once a day everyday it gives me either a e0020-0101 or a e0020-0103. Customer powere off/on for it to start working again.
Error in yellow and cyan developing...
I have no idea sir,
could it be the firmware?
i have a konica pro c754 with a message on the command workstation giving me an error s1 and s2.
everything seems to be working perfectly fine.
i have cleaned the optics even though it was...
Fixed
i replaced the ops panel assy. Under warranty anyway
thanks everyone
Will it still upgrade firmware even with the screen blank?