DF-701 dead with C-9403, black (displayport) cable replaced, CIS replaced, small PWB near CIS replaced, suspected DS board.
Yes, there is the entry DF-624. I'll try and report it ;-)
Of...
Type: Posts; User: lordqpa
DF-701 dead with C-9403, black (displayport) cable replaced, CIS replaced, small PWB near CIS replaced, suspected DS board.
Yes, there is the entry DF-624. I'll try and report it ;-)
Of...
Hi my friends,
Does anybody try to install df-624 to c454?
My df-701 is dead and I'm f for cheaper solution. :)
That machine doesn't print and copy, doesn't show supplies status and doesn't print aby test and report page.
Panel looks normaly. Diagnostic shows error 303-316-00.
Any sugestions?
Hi,
I've got the same problem with 224e. After c2557 toner level is 0.5%. I did perform Manual Add Toner. Toner level were 6% but it's were for a while. After few 100s pages problem return. Any...
Does anybody know differences between toners TN-612 and older KM toners for colour machines (c350, c252 ...)?
Does anybody use TN-612 for c350 or c351? Older toners (powder) are compatible.
Two ways:
1) Replace take up roller
2) High voltage leakage (damage drum or/and mag. roller seal - drive side)
I need info about how to reset couter of Main Charger (MC-81) in FS-5900c.
Service menu contains only Status Page, Test Page 1, Test Page 2 and Type TransferRoller X or Y or Z.
Thx
U should set some foo data in SMTP and POP3 settings in network section.
Generaly PH Unit (laser) malfunction:
C13F4 Optical System out of adjustment range
C13F5 LD1 intensity adjustment failure
C13F6 LD2 intensity adjustment failure
C13F7 Sub-scanning direction...
If skews are only in 1st tray, i'm affraid that problem is bushings on registration rollers. One bushing (near registration clutch) wipe away and rollers don't have equal pressure. Try reasembly and...
You only need add SU-2 module. No update of firmware is needed. I suppouse you have print controler and network card in machine. Scan options will enable after SU-2 module is istalled.
Welcom !
Please tell me how to change web interface/panel display (setting section) language in IP-422/IP-423 Konica controller. Current I've got Italian or Spanish language. I wanna have English.
Use webrowser, type IP addres of bizhub and go to Scan -> Adress Book, FTP addresses are from 245 to 255 (down side of the page). After setup address go to machine and press SCAN button next Adress...
Power supply 230V -> 5V
Connections and other in attachment:
Hdd is normal 2.5" disk. U need flat cable to connect to MB and 5V power supply unit. I used cheap 5V supply from market.
Good luck.
This machine hasn't support SMTP Auth so email scanning is difficult even impossible.
I've been replaced Control Board (located right side of the rear under IP controller cover). Machine displays F81-2. Control Board is from 7235 but machine is 7228. I dowloaded control firmware...
Hi !
I cannot remove drum unit in Di 470. I loose all screws but unit stacks. I tried force - unsuccessful, machine sputters only.;-).
Is it nessesary disasembly rear side and try remove drum shaft...
I've been looking for it on Infohub without success :(
Below are links to screenshots from Infohub:
http://en.fotoalbum.eu/images/7432/408667/00000001.jpg
...
This is Fixing Error. Low Temperature. Try:
Localize hole on right side of control panel. In hole is switch. Press it. Machine will restart. Enter “3” from the 10-Key Pad when dot appears at the...
I need system for IP-511 Type A e.g. 6.3.0 or higher. On Europe infohub are only upgrades. Hard disk is damaged. DOS starts. Command d:recovery not works. I need information about partitioning hdd...
Does anyone have the bin files for the CF2002/3102 and could Email them to me karolo(at)intelline(dot)pl. I will resend bins for C350 or CF1501.