My Ricoh Aficio MP C6000 needs to replenish Black drum developer.
I can't figure out how to pull the developer unit in order to get at the four drums.
I Removed the upper left and right screws but...
Type: Posts; User: ybnews
My Ricoh Aficio MP C6000 needs to replenish Black drum developer.
I can't figure out how to pull the developer unit in order to get at the four drums.
I Removed the upper left and right screws but...
My Ricoh MPC 6000 showing code SC540.
Fuser unit is jamming. Opened up D2 cover, Turning blue D1 knob is stiff and bumpy.
Top fuser pressure roller to the left of the fuser heat roller almost looks...
Looking at purchasing used ir 8500.
2 million copies. $900
wondering if this model iS high maintenance?
Thanx.
Greetings.
I'm looking for a used, developer unit for the internal parts (auger) for my Toshiba, estudio 2100c color copier.
Any color unit will do Y.M.C.K.
The following models developer units...
Hey Vigour,
I think you're onto something.
Will look into these suggestions.
I'll report back later.
Thanx,
Dana
It happens in every tray and every draw.
Here's a new observation,
First sheet out is skewed 1/4" to the left.
All sheets after that are centered.
Same thing in both draws and all 3 trays....
Canon IR 600 margins need to be re-set.
When making copies from either the glass or electronically from my computer the image is not centered.
From the lead edge, (top left corner) of the glass,...
When I use the ADF Scanner the copies come out with a dark shadow along the bottom (operators side)
If I set the exposure to the lightest setting before feeding it gets lighter>
When I set exposure...
Yea,
I figured as much from the deafening silence to my request for assistance.
This community has always been incredibly helpful in the past and gotten me out of many issues.
In the motorcycle...
E Studio 2100c booklet finisher throws message "close finisher door" when hooked up to machine.
When I open the Top door or the upper front door cover the message changes indicating the micro...
It already has issues...
The rubber fuser belt has self destructed as it slowly migrated sideways from left to right and peeled apart as it rubbed against the machine.
Anyone know how to correct...
Is the Nothing good to say about this copier???
Hi,
I just looked at a used E Studio 2100C that was listed on my local Craigs List.
It booted up and made decent copies from the glass.
The seller is the original owner and it was leased thru...
Yes,
Still have streaking issues...[
QUOTE=ybnews;387360]Dark horizontal streaks across the sheet for first six or so copies.
Streaking gets lighter after that amount but still unacceptable...
Dark horizontal streaks across the sheet for first six or so copies.
Streaking gets lighter after that amount but still unacceptable quality.
When I jam a wadded up piece of paper under the middle...
All drive gear turn freely.
Checked take-up roller feed.
Left, feed is Under, Right roller is Over.
Solenoid motor turns freely when removed from machine.
Shaft does not.
I can hand operate the L-shaped lever that detects...
My Canon IR 6000 cleaning web take-up roller does not turn.
Assuming I have installed it correctly, the empty, take up shaft is on the left and the Full, roller with clean web material is on the...
My Risg GR3750 has an issue.
Every master I make on Any cylinder I use the image prints more than 1 inch to the right of the lead edge. There's not enough range in the "print position" button to...
PROBLEM RESOLVED! I sent control panel back to Hytec. They sent me a new one under warranty. I installed it and was able to re-set the original error code. Huge Thanks all here and to Hytec for...
Just got off the phone with Hytec.
Canon rep said control panels for 550's and 6000's notoriously bad.
They gave an RA# and said they'd sawp it out under warranty.
I hope the next one comes back...
blazebusiness, You're right. Model is IR 6000 (not 600). I removed the fuser unit, checked out all connections, unplugged and re-plugged lamp wires and wrapped w/ electrical tape. Reassembled. No...
Hi tekcat.
Thank you for your suggestions.
Main thermistor checks out. Tried power up with door open. Touch Screen still does not respond to my touch and still goes dark after 60 seconds. Fuser...
In the middle of a booklet run my IR 600 shut down displaying E000001-000
I turned off power, unpluged and waited about 10 minutes till it cooled down.
I checked the fixing roller web. It was...
I'm in Massachusetts.
I found a guy with NO hair.
Said he might drop in sometime soon.
Gotts my fingers crossed.