Nah, after stripping the finisher it came out eventually but no easy procedure. I had the broken gear to fit to the exit unit (cost almost nothing) but then realised that it was a bugger to replace -...
Type: Posts; User: Konicoz
Nah, after stripping the finisher it came out eventually but no easy procedure. I had the broken gear to fit to the exit unit (cost almost nothing) but then realised that it was a bugger to replace -...
thanks everyone for all your input and suggestions and your time to respond. I think I have enough info to make a decision and majority rules . I am going to say no to alcohol and only keep a small...
Thanks for the post. I have seen this happen as well, usually the engineer gets carried away and spray and prays and the oil is transferred through the machine and is a bugger to clean out. WD40 on a...
Thanks for the post - used acetone once and never again - dangerous stuff :)
Good morning everyone.
In our small group of technicians a question has been raised that has left us divided and undecided. I need your experience and wisdom to settle this question
'Is using...
Good morning everyone.
In our small group of technicians a question has been raised that has left us divided and undecided. I need your experience and wisdom to settle this question
'Is using...
Haha I am doing this now...looking like a tool giving them their old machine back after Salesman told them they had to upgrade cause theirs was old and useless, want to take off my Konica shirt in...
don't like them myself. control panel failures, fuser fails, print/ copy quality is so/so - cheap feel to them and warranty is couple of months. Better than C35 series though.
Hi Guys is there a common reason why the doc blade flips on this model. Had a machine flip the black blade and has been replaced with new - now 2 weeks later yellow and Cyan have flipped?? leaves a...
first time I worked on one was before training - error AA and a major pain in the ass, things got way out of hand. So I went on Fiery advanced colour training and they decided to do an extra day to...
I am also new to fiery and don't have clone tool...went on fiery ILT at konica last year and when I asked about that he said "No not allowed to use that - its illegal..." although on the forums I...
hey guys - I cant figure out how the darn exit unit comes out of the FS-534 - pretty much stripped the finisher down and the bugger is loose but not out.
I have error c-1184 and the gear that drives...
2 new fusers - fuser drive assy and exit drive assy - half a barrel of oil all over exit and transport rollers and 4 hours later - still noise.....aaaaarg!
next part I order is a grenade......
Duh can you believe I come all the way here and press the buttons and voila - working- aaaarg such a long way to travel for that......
I am setting up that remote panel- it's 23:30 and maybe just...
I know the lady goes on leave today so I will get another operator to try - might have better luck with her
thanks emujo I will try it with some one closer and see if I can do it..
Hey guys. I have a wonderful customer that's just down the road at a rural mine site, only 1600 kms away round trip. It has a transfer belt error (end of life) I know how to turn the machine stop at...
hi- read the documentation for the firmware, you have to change ssw bit 25 i think, cant remember what that version is but it should tell you in the documentation. once you have done that it will...
bwahahaha virgins :)
Thanks for all the help guys, yeah the customer was pretty pissed, I couldn't go but one of my colleagues went and performed all steps just to be safe, only dif was he...
Spock - maybe I should know.. but I am not familiar with the mfp reset tool / are you talking about the reinitialize to factory default setting? can you clarify, thanks
we have tried new memory...
hey guys - yep another weird fault. I have had my fair share of these m/c's freezing and not booting up and not waking up. This particular machine is not even 2 weeks old and has account track set...
In my opinion after working with them both for just over 2 years
best of Kyocera
B&W range
Tech friendly (except TA range access to drum area...)
Boards and electrical (but some connectors are...
print, copy and fax and .......
25689
hey guys a customer asked me why is this OKI fax is giving these errors. I don't work on them so just helping him out- kind guy I am....
He sends jobs to these numbers everyday - sometimes...
Guys thank you all for your input, I tried it today on a machine and its exactly what I needed - simple and effective. Thanks a lot...
If I could I would buy you all a drink \_/
...
hey guys, just looking at some posts and helping who I can where I can and picking up useful info....I came across this PPLM mod in a post to extend or turn off dev and drum alerts for c360...